FINISH MOWER by Owner’s Manual This manual contains important safety instructions for the gasoline engine powered lawnmower models: 26FB READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS CAREFULLY. SAVE THIS MANUAL. Insert Illustration of the mower Need Help? Parts, Service and Technical Assistance call: 1-919-550-3221 www.brushbeast.
TURF BEAST 26FB Copyright© 2009 by GXi Outdoor Power, LLC. All rights reserved. No part of this publication can be reproduced or distributed without prior written permission of GXi Outdoor Power, LLC USA. BEAST and DEK is a registered trademark of GXi Outdoor Power, LLC GXi Outdoor Power, LLC reserves the right to discontinue or change specifications or design at any time without notice and without incurring any obligation whatsoever.
BEAST SERIES Check out our other great products at www.HomeDepot.com or visit our web site at www.brushbeast.com Turf Beast Turf Beast 36-inch Walk Behind 54-inch Walk Behind The Beast 100-inch Tow Behind Mower Brush Beast Brush Master 36-inch Brush Mower.
TURF BEAST 26FB Contents Safety Information and Warnings .................................................... 1 Operation Safety Precautions ......................................................... 2 Safety Decals .................................................................................. 3 Product Specifications .................................................................... 4 Control Panel and Lawn Mower Components .................................
TURF BEAST Safety Information and Warnings Mower Inspection Safety Information For your safety, inspect the lawn mower before each use. Before you begin your inspection, be sure the following conditions are met: the lawn mower should be on a flat and level surface, with the ignition switch off, the key removed, and the blades disengaged. Also, disconnect the spark plug wires from the spark plugs and ground them against the engine to prevent inadvertent starting.
TURF BEAST Operation Safety Precautions 9. Never operate the mower with defective guards or shields, or without the safety devices securely mounted in place. 10. Never direct discharge of material toward bystanders nor allow anyone near the mower during operation. 11. Do not change the governor settings or over speed the engine. 12. Always stop the engine when you leave the mower, even for a moment. 13.
TURF BEAST Safety Decals 26FB Safety Decal Identification The labels shown below are located on your mower to warn you of potential hazards and provide you with important safety information. If these decals become difficult to read or are missing from the mower, please contact GXi Parts & Service, LLC at 1-919-550-3221 or www.brushbeast.com for a replacement.
TURF BEAST Product Specifications Models Feature 26FB Product Type Walk behind mower Cutting Width 26-inch Engine Engine Start Transmission Type Mower Speeds Deck Type Cutting Height ## inches Blade Engagement Manual clutch Blade Tip Speed 18,750 ft/min Anti-Scalping Rollers None No. Blades/ Length #, ##-inch blades Control System Fuel/Capacity Gasoline/## gals.
TURF BEAST Control Panel and Lawn Mower Components 26FB Throughout this manual, instructions are given on the operation of your TURF BEAST mower. We recommend that while going through this manual, you have your mower available for quick and easy access in order to orient yourself with the controls, maintenance and orientation of different parts. Please read through the manual before operating. Control Panel Below, you will find a diagram of the control panel.
TURF BEAST Missing Parts Missing Parts Request Form Please indicate the part that you are missing: Hardware bag Wheel Kit Name Other Address Date of purchase Model #: 26FBM15 Other Phone Email Serial #: Comments: IMPORTANT: Please include a copy your receipt. Without a receipt, your order will be delayed. E-mail : customerservice@gxioutdoorpower.com Fax: 1-919-550-3277 Please scan and attach your proof of purchase to your e-mail.
TURF BEAST Assembly Instructions Step 1: Front Wheel Assembly Note: Some mowers may be shipped with the front wheels pre-assembled. A. Remove packaging materials surrounding the front wheels and remove the bolt threaded into the front wheel. Retain this bolt and washer for future use. B. Unscrew the fastener holding the bolt to the steel shipping rack. Set the nut and bolt aside. It will be re-used in the mower assembly process. C. Remove the mower from the steel shipping rack. D.
TURF BEAST Assembly Instructions 26FB Step 2: Mower Assembly Instructions A. Attach handle bars using the upper hole position setting. Using this hole position sets the handle bars several inches lower. Use the lower hole position raising the handle bar location by several inches for comfort, if necessary. These hole positions can also be used for adjusting the handle bar location for operators of different heights and arm lengths. Select the height that is most comfortable for you. B.
TURF BEAST Assembly Instructions 26FB Step 3: Wire Harness Assembly and Connections The pre-wired handle bar assembly has a total of four (4) connections. Route the wire harness as shown in the top right photo and make the following connections indentified by number in the other photos: 1. Route the smaller, white, 2-pin connector through a hole in the chassis and connect it to the blade activation safety switch 2-pin connector. 2.
TURF BEAST Assembly Instructions 26FB Step 5: Fuel tank connections Locate the fuel tank on the fuel tank bracket with the recessed area pointing toward the rear so any spills drain away from the engine. Align the fuel valve in the center of the clearance hole. Place the fuel tank straps into position, wrapping them around the tank and the bracket. Battery pan Once the fuel tank and straps are in place, securely tighten the straps using the bolts provided.
TURF BEAST Operating Instructions 26FB Starting the Engine Operating the Mower 1. Make sure the brake has been moved to the OFF Position. 2. Push down and hold the operator presence control levers on the handle bar with both hands. 3. The forward and reverse levers are spring loaded to the neutral position. 4. To drive the mower forward, slide both hands slightly back on the handle bar and gently squeeze the forward levers toward the handle bar.
TURF BEAST Operating Instructions 26FB Disengaging Hydrostatic Drive Units Return to Neutral Before physically moving the mower when the engine is NOT running, the hydrostatic drive units need to be disengaged into free-wheel mode. If the mower creeps or will not stop as desired when the handles are in neutral position, adjustments are necessary. CAUTION: Be sure the engine is OFF before you open the hydro access panel. 1. Remove the bolts to access hydro panel.
TURF BEAST 26FB Mowing WARNING WARNING! Thoroughly inspect the area where you plan to use the mower. Look for items such as stones, sticks , wire, and other foreign objects. If struck by the mower, these and other objects may become projectiles that could lead to serious injury or death. Clear area of all debris. Keep people and pets at a safe distance. WARNING WARNING! Do not operate the mower with defective guards, shields, or without the safety devices securely in place. 1. XXXXXXXXXXXXXXXXXXXXXXX.
TURF BEAST Operating Instructions Changing the Height of Cut 3. XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXX X XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX How to Change the Cut Height 1.
TURF BEAST Maintenance XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XX Rev: July 2015 TURF BEAST Finish Mower 16 26FB
TURF BEAST General Maintenance Fuel The Importance of Maintenance Regular maintenance is essential to ensure your mower continues to deliver safe and high-quality performance. DANGER DANGER: Gasoline is highly flammable and explosive. Do not add fuel while the engine is running or is hot. Keep open flames, sparks, and heat away from the fuel and store fuel in containers specifically designed for that purpose. Add fuel outdoors only and if the fuel is spilled, do not start the engine.
TURF BEAST 26FB Maintenance Schedule Time Interval Item Break-in Every 8 (first 5 hrs hrs) (daily) Procedure Blades Inspect and Sharpen X Engine Air Filter Inspect (see Engine Owner’s Manual) X Engine Cooling Areas Clean Every 25 hrs (weekly) Every 50 Every 100 hrs hrs (Bi-weekly) (monthly) X Check X Engine Oil Change X X Engine Oil Filter Change X X Engine Spark Plug Inspect Fuel Filter Replace Fuel Line Check Hardware Check for proper tightness Mower Main Frame Remove d
TURF BEAST Service Adjustments Removing and Changing the Blades 3. XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXX X For maxmimum performance, keep balde straight and sharp. CAUTION! Beware of the cutting edges on the blades. Stop engine and wait for all movement to stop before removing blade (s) Always wear work gloves when handling blades. Required tools: CAUTION XXXXXXXXXXXXXXX 1. XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXX 2. XXXXXXXXXXXXXXXXXXXXXXXxxx 3.
TURF BEAST Service Adjustments 26FB DANGER DANGER: Before making any adjustments or servicing your mower, make sure the mower is on level ground, the blades are disengaged, the key is removed, the engine is off and the spark plug wires are disconnected from the spark plugs to prevent inadvertent starting. If maintenance or adjustments are being performed after operation of the mower, allow the unit to cool since heat build up could cause severe burns.
TURF BEAST Service Adjustments Change Engine Oil 26FB Safety System Adjustments 1. XXXXXXXXXX WARNING WARNING: Do not bypass, modify, alter, or disconnect the safety system. Make sure that the safety interlock system is fully operational each time before mowing. Failure to do so could present danger to you and others around you. XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXxxx Thottle Cable 1.
TURF BEAST Service Adjustments Underside of mower Cleaning 26FB TRANSPORTING When transporting the mower, turn the engine switch and the fuel valve OFF. Keep the generator level to prevent fuel spillage. Fuel vapor or spilled fuel may ignite. Take care not to drop or strike the generator when transporting. Do not place heavy objects on the generator. When transporting the generator by loading it on to a vehicle, secure to the generator frame as shown.
TURF BEAST Service Adjustments 26FB To ensure proper lubrication of moving parts, GXi recommends that you lubricate the following components with a high-quality, EP2 high-temperaturebased grease or equivalent. Should the conditions of operation be more severe than normal, the lubrication interval may need to be shortened. GTR/OPE grease is the recommended lubricant. Lubrication Point Locations 26-inch mowers have XX lubrication points Lubricate after every 20 hours of usage 1.
TURF BEAST Troubleshooting Problem Possible Causes Solution Engine will not start 1. 2. 3. 4. 5. 6. Key in the OFF position Insufficient fuel in the tank Air bubble in the fuel line Fuel valve in OFF position Choke not ON Choke linkage out of adjustment 7. Low engine oil 8. Blade control in ON position 9. Loose spark plug wire 10. Fouled spark plug 11. Plugged or dirty air filter 12. Bad gasoline 13. Plugged or dirty fuel filter 14. Safety switches out of alignment or loose 15.
TURF BEAST Troubleshooting 26FB Problem Possible Causes Solution Mower will not move forward or reverse 1. Brake ON 2. Bypass levers pulled out 1. Release brake on control panel 2. Ensure bypass pins are retracted Cannot move mower when the engine is off 1. Bypass not engaged 1. Pull left and right bypass pins and set them in slots in the chassis (p. 11) Engine is overheating 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 6. 7.
TURF BEAST Rev: July 2015 Parts Diagram TURF BEAST Finish Mower 26 26FB
TURF BEAST Rev: July 2015 Parts Diagram TURF BEAST Finish Mower 27 26FB
TURF BEAST Limited Warranty & Service 26FB Length of Warranty: *(from the date of original retail purchase) Products Covered by this Warranty Residential Commercial Rental Engine 2 years limited 90 days limited 90 days limited Mower frame Lifetime (original owner only) Lifetime (original owner only) 90 days Tires, Filters, Battery Attachments 90 days 1 yr limited 90 days 1 yr limited 90 days 30 day limited *LENGTH OF WARRANTY: Batteries supplied with applicable products as standard, origi