D I A M O N D C O R E R I G S ® BCR 130/5 BG BCR 130/5 MG BCR 300/12 OPERATING MANUAL
CONTENTS General Power Tool Safety Warnings. . . . 6 For your safety. . . . . . . . . . . . . . . . . . . . . . . . . 7 Tool Specifications. . . . . . . . . . . . . . . . . . . . . 8 Operating Controls. . . . . . . . . . . . . . . . . . . . . 9 Safety guidelines. . . . . . . . . . . . . . . . . . . . . . . 9 Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . 9 Before Use. . . . .
BCR 130/5 BG 1 11 10 9 8 7 2 6 3 5 4 BCR 130/5 MG Compact 12 13 14 15 16 24 17 25 18 26 19 27 28 20 21 22 29 23 Compact III
32 31 6 33 34 32 33 34 IV BCR 130/5 BCR 300/12
BCR 300/12 12 1 2 4 47 36 35 9 14 19 13 3 8 7 15 17 6 30 20 21 23 22 Large Large 38 39 24 40 25 41 26 42 27 43 28 44 37 45 29 46 Vacuum pump V
® BCR130/5-BCR300/12 GENERAL POWER TOOL SAFETY WARNINGS WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
® BCR130/5-BCR300/12 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
® BCR130/5-BCR300/12 Vacuum pump •• •• •• •• •• Avoid any constrictions in the suction hose, e.g. due to dirt accumulation, squeezing, bending or stretching. Check the suction hose each time before use. Renew any leaking or damaged parts. Keep the cooling air vents on the pump free and clean. The underlying surface of the drill stand must be clean, firm, smooth, dry and without any holes. For further safety regulations, see the operating instructions for the drill stand.
® BCR130/5-BCR300/12 OPERATING CONTROLS SAFETY GUIDELINES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 The definitions below describe the level of severity for each warning. Please read the operating manual and pay attention to these symbols.
® BCR130/5-BCR300/12 Always use the correct supply voltage: The power supply voltage must match the information quoted on the tool identification plate. INITIAL OPERATION Functional test for the GFCI protective switch 4 WARNING: The ON/OFF switch 2 must be switched off, in order to avoid unintentional starting of the machine when carrying out the functional test of the GFCI protective switch 4.
® •• BCR130/5-BCR300/12 After the bit is guiding itself into the material, swivel back the machine into the right angle position. Hand held dry drilling DRILLING WITH A DRILL STAND Guide block setting A B Mounting the dry drilling kit 10 A B •• •• •• •• •• •• Loosen the frontgrip 5 of the core drilling machine. Mount part A of the dry drilling kit onto the drill spindle 6. Slide the dry drilling sleeve (B) on part A in the desired position for the vacuum cleaner. Tighten the grip 5.
® •• BCR130/5-BCR300/12 WARNING: Maximum drilling diameter of 4”. Mount the drill stand on an even, firm and smooth surface using the vacuum pump, never “over” head. Always connect the core drill and the vacuum pump to the same power outlet. Never turn off the vacuum pump during operation. plate is located directly above the required drilling location. Fasten the drill stand. Setting the drilling angle •• •• •• Loosen the clamping lever 17.
® BCR130/5-BCR300/12 OVER HEAD DRILLING DANGER: When drilling “over” head always secure the drill stand with the assembly. DANGER: When drilling “over” head, always use a water collecting ring and a industrial wet-type vacuum cleaner! Mounting the water c ollecting ring 34 •• •• •• •• •• Loosen the fixation screw 33 on the water collecting ring 34. Push the water collecting ring 34 onto the drill stand and press it firmly against the material to be drilled. Tighten fixation screw 33.
® Problem The motor doesn’t work. BCR130/5-BCR300/12 Possible cause Defective motor. Defective cable of plug. Motor makes too much noise. Motor mildly overheats. Defective switch. Damaged windings. The carbon brushes of the machine are worn. Motor overload. Motor doesn’t cool sufficiently Motor runs. Core bit doesn’t rotate. Rate of drilling progress decreases. Gearing defective. Core bit segments polished. Water pressure/water flow rate too high. The core is stuck in the core bit.
® BCR130/5-BCR300/12 REPLACEMENT PARTS If – in spite of meticulous manufacturing and testing processes – the device breaks down, have it serviced by a BEAST/B+BTec Service. The typical hand-arm vibration is below 2,5 m/s2 (EN-ISO 5349). Wear ear protection! C DECLARATION OF CONFORMITY GUARANTEE For this BEAST/B+BTec appliance we grant a warranty in accordance with the statutory/countryspecific provisions as from date of purchase (by evidence of invoice or delivery note).
110 V BM1604 BEMBCR-1612V4 LACKMOND.
