B E A S T R A I L S A W S ® RS34 RS48 RS59 OPERATING MANUAL
® RS34 - RS48 - RS59 CAUTION: Carefully read and understand all Safety and Operating Procedures prior to using the Beast® machine. Keep this Manual in a safe place for future reference ATTENTION: As our engineers are constantly conducting research and development on our machinery to develop quality products for the marketplace, our product model(s) can be changed without notice. CONTENTS Beast Safety. . . . . . . . . . . . . . . 3 Safety Messages . . . . . . . . . . . . . . . .
® RS34 - RS48 - RS59 BEAST SAFETY It is extremely important that you read and understand all of the safety instructions, the operating instructions and the maintenance instructions. If these instructions are not followed, serious injuries and/or death could occur to you or to others. Also, failure to read and follow the enclosed maintenance instructions can lead to equipment failure, damage to the equipment or reduced lifetime of the equipment.
® RS34 - RS48 - RS59 ing area well lit. • CHILDREN SHOULD BE KEPT AWAY FROM THE WORKING AREA Only the operator of the equipment should be in the working area. All other people especially children should be kept away at a safe distance. • KEEP THE WORKING AREA CHILDPROOF It is important to keep the working area child proof. This can be done by using locks on the equipment, plastic plugs for the electrical outlets and possibly even master switches on the equipment.
® RS34 - RS48 - RS59 owner’s manual for determining what are the recommended accessories to use with this type of equipment. Using accessories that are not recommended in the owner’s manual may increase the risk of personal injury and/or to people that are within close proximity of the machinery. • CHECKING THE EQUIPMENT FOR DAMAGED PARTS. It is important to inspect the power tool before using it to check for damaged parts.
® RS34 - RS48 - RS59 • KEEP AWAY FROM MOVING PARTS It is important to keep hands, feet, hair and clothing away from all moving parts to prevent injury. It is also important to be sure that covers and guards are always in their proper position. If not, serious injury can occur. • DO NOT REMOVE BLADE GUARD It is important that all machine guards remain in place and in proper working condition. This is to prevent serious injury, death or damage to the equipment.
® RS34 - RS48 - RS59 risk of electric shock. The equipmentgrounding conductor is the insulated conductor that has an outer surface that is green with or without yellow stripes. If repair or replacement of the electric cord or plug is necessary, do not connect the equipmentgrounding conductor to a live terminal. • Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubts to whether the tool is properly grounded.
® RS34 - RS48 - RS59 WARNING: It is important to not abuse the extension cord and do not yank on any cord to disconnect it from the outlet. WARNING: It is important to keep the cord away from heat and sharp edges. WARNING: It is important to disconnect the extension cord from the outlet before disconnecting the machine from the extension cord. WARNING: It is important not to use an extension cord that is undersized.
® Water pump RS34 - RS48 - RS59 Blade guard sure most water flows back in the water container. UNPACKING & SETTING UP Cutting table Unpacking and Assembly • Unpack the tile saw and inspect for any damaged parts. • Install the legs in the sockets at the under side of the water container and fasten with the knobs. Markings show the right position. • Level the tile saw by adjusting the legs in the sockets and make sure its stable. • Release the transportation lock. Saw spindle Detachable legs spindle.
® RS34 - RS48 - RS59 Setting the Cutting Depth CAUTION: By loosening the knob the saw head can be positioned at the desired height. The saw head is tightened by a spring and may accidentally jump up when the knob is loosened. Motor protection The motor is equiped with a thermal safety switch for protection against an overload. When the motor gets overheated, the switch falls back into its initial position and can only be switched on again after the motor has cooled down.
® RS34 - RS48 - RS59 OPERATING INSTRUCTIONS • Position the cutting head at the desired height • Hold the material with one hand while making sure your hand is free from the cutting blade. • Perform the cut. This process must be repeated until the material has been totally cut through. • Turn the motor OFF when work is complete. Single Step Cutting DO NOT FORCE THE TOOL! It will do the job better and safer at the rate for which it was designed. Use original Beast® wet cutting blades only.
® RS34 - RS48 - RS59 MAINTENANCE & TROUBLESHOOTING General Maintenance • The cooling water should be replaced and/or replenished regularly. • It is recommended to clean the water container, pump, hoses and spray nozzle on a regular basis. For example, place the pump in a bucket of clean water after the sawing job and run the machine for a minute or so. This also guarantees a longer lifetime of the pump. Diamond blade dressing Diamond blades performs best when they are dressed.
® RS34 - RS48 - RS59 Troubleshooting The machine does not work. - The power supply cable is damaged or not properly connected. - No voltage in the power outlet. - Start Switch is damaged. - Press the plug firmly in the power outlet. Check the power supply cable. - Have the power outlet checked. - Have the Switch replaced. Water does not flow at the blade while the pump is running. - The sprayers are clogged. - The water level in the waterbin is not sufficient. The pump is not totally submerged.
® RS34 - RS48 - RS59 Spare Parts 1 6 3 11 4 10 5 2 7 9 8 Pos. # Item Nr. - 2 HP Description 01 6.516.005 Motor 02 6.513.022 Switch 03 4.259.026 Motor Flange 5/8” 04 4.259.007 Saw Flange 05 6.516.006 Flange Nut 06 6.513.021 Capacitor 07 6.513.298 Pump 08 6.509.011 Knob 09 6.509.065 Adjustable Handle 10 4.259.040 Guiding Roller & Bearings 11 6.509.
® RS34 - RS48 - RS59 OPTIONAL ACCESSORIES Side Table with squaring arm Dimensions: 16” x 16” Qty. 1 LPI# BRS ST GFCI Switch Qty.
BEMBRS-1612V2 LACKMOND.