Installation Guide

ManualsBrandsBeaumont Decor ManualsBathroomHampton 37-in White Single Sink Bathroom Vanity with White Natural Marble Top

INSTALLATION GUIDE

P 1

MODEL

Bolts (4) Undermount clips (4)

Washers (4) Wing nuts (4)

A B

HARDWARE

NEEDEDINCLUDED

Permanent marker

Silicone - (Recommend Liquid Nails

#LN-933 OR Loctite GE Silicone II

#M90010)

Epoxy - (Recommend Loctite

#1365868 OR Gorilla Glue #4200101)

Caulking gun

•

Base cabinet

Countertop

Sink basin

Backsplash

Hardware

•

STEP 1 - PLACE & TRACE STEP 2 - PREPARE SINK BASIN

Place the sink basin on the bottom of the countertop,

making sure to center over the opening. Draw guide

lines on the countertop and the basin in two locations.

Using a caulking gun, apply a heavy amount of

silicone of your choice on the top side of the sink

basin edge.

STEP 3 - FLIP & SET IN PLACE

Carefully flip the sink basin over and place it so the

guide lines match up in both locations.

STEP 4 -

DRY & SET

Press down on the sink basin to seal the silicone.

Remove any excess. Follow dry time recommendations

found on your product, typically 12 to 24 hours.

Summary of content (4 pages)

PAGE 1
INSTALLATION GUIDE INCLUDED NEEDED • Base cabinet • Permanent marker • Countertop • Silicone - (Recommend Liquid Nails #LN-933 OR Loctite GE Silicone II #M90010) • Sink basin • Backsplash • Hardware HARDWARE A • Epoxy - (Recommend Loctite #1365868 OR Gorilla Glue #4200101) Bolts (4) C Undermount clips (4) D • Caulking gun Washers (4) MODEL B Wing nuts (4) STEP 1 - PLACE & TRACE Place the sink basin on the bottom of the countertop, making sure to center over the opening.
PAGE 2
EPOXY INSTALLATION GUIDE D A A C B STEP 5 - PREPARE & SET BOLTS Fill in the small holes surrounding the sink basin with epoxy. Immediately place the top of the bolt (PART A) in the hole with the epoxy. Allow sufficient dry time & follow the package directions on the epoxy before moving to the next steps, typically 12 to 24 hours.
PAGE 3
GUIDE D'INSTALLATION INCLUS NEEDED • Meuble bas • Marqueur permanent • Comptoir • Silicone - (Recommander Liquide à ongles # LN-933 OU Loctite II n ° PL530 ou Silicone GE # M90010) • Lavabo • Dosseret • Matériel MATÉRIEL A • Epoxy - (Recommander Loctite # 1365868 OU Colle Gorilla # 4200101) Boulons (4) C Clips de montage (4) D • Pistolet à calfeutrer Rondelles (4) MODEL B Écrous à oreilles (4) ÉTAPE 1 - PLACE & TRACE Placez le lavabo sur le fond du comptoir en veillant à centrer l'ouverture.
PAGE 4
EPOXY GUIDE D'INSTALLATION D A A C B ÉTAPE 5 - PRÉPARER ET RÉGLER LES BOULONS Remplissez les petits trous entourant le lavabo avec de l'époxy. Placez immédiatement le haut du boulon (PARTIE A) dans le trou avec l'époxy. Laissez suffisamment de temps de séchage et suivez les instructions de l'emballage sur l'époxy avant de passer aux étapes suivantes, généralement 12 à 24 heures.