® HOUSTONIAN STANDING SEAM METAL AWNING OWNER’S MANUAL & INSTALLATION INSTRUCTIONS (For 3ft and 4ft Widths)
Table of Contents Contents ATTENTION: Warning Requirements ............................................................................................................ 2 Hardware for Different Surface Applications ............................................................................................... 3 Parts List ........................................................................................................................................................ 4 Parts Included: .................
ATTENTION: Warning Requirements WARNING: Adult Assembly Required WARNING: Assembly Kit Contains Parts With Sharp Points, Sharp Edges, and Small Parts That Can Present Choking Hazards to Children. WARNING: Components Are Packed In Plastic Bags That are a Suffocation Hazard. NOTE: Please inspect the parts for damage during shipping and/or for any missing items. If you suspect that there may be damage or a shortage, contact us and we will send replacement parts if needed.
Hardware for Different Surface Applications Before you begin the assembly, there is a variety of building wall surfaces; Awntech does not supply the hardware to install your awning. You will need to purchase installation hardware at your local hardware store.
Parts List Parts Included: Part Image Part Name Part # 3ft 4ft Black Nylon "L" Connectors a 4 4 Full Top Bar (with extenders) for 3ft & 4ft b 1 1 Front Bar (with hook extenders) for 3ft & 4ft c 1 1 Left Frame d1 1 1 RightFrame d2 1 1 Spines e 3 4 Sheet Screws f 26 34 Left Panel g 1 1 Middle Panel h 2 3 Right Panel i 1 1 Left Back Bar j1 1 1 Page | 4
Right Back Bar j2 1 1 Left Projection Bar k1 1 1 Right Projection Bar k2 1 1 Bolt for Projection and Back Bars l 6 6 Nut for Projection and Back Bars m 6 6 Full Shroud (Hood Cover) n 1 1 Parts Not Provided: Part Image Part Name M8 Anchor or M6 Anchor (Depending on surface) Part # 3ft 4ft o 4 4 Page | 5
Assembly for 3ft and 4ft Width Houstonian Awnings For video assistance on assembly please go to our youtube link: https://youtu.be/G44LiwmYEGY Step 1:Count every part to make sure you have the proper amount for your specific awning width size (ft).
Step 3:Insert the Spines onto the Full Top Bar and Front Bar Parts you will need for a 3ft: 3-(e) Spines, 6-(f) Sheet Screws, 1 Drill Parts you will need for a 4ft: 4-(e) Spines, 8-(f) Sheet Screws, 1 Drill a) Using a drill and (f) sheet screws, connect the ends of each (e) Spine to the pre-drilled holes on the (b) Full Top Bar and the (c) Front Bar (with hook extenders). The larger holes on the (e) Spines will connect to the (c) Front Bar (with hook extenders). Refer to the figure below.
b) Begin with the (g) Left Panel; the starting panel. Make sure the left side of the (g) Left Panel is the side/lip hanging down over the (d1) Left Side Frame. This will cover the left side of the awning frame when the (c) Front Bar is closest to you.Refer to the figures C1 and C2 below. c) Apply the (h) Middle Panels as shown in the figures below.
Figure D1:Input (f) Sheet Screws into the (c) Front Bar Figure D2:Input (f) Sheet Screws into the (b) Full Top Bar Figure D3: Input Sheet Screws into the Left Frame and Right Frame Page | 9
Step 6:Attaching theBack Bars to the Full top Bar Parts you will need for a 3ft: 1-(j1) Left Back Bar and 1-(j2) Right Back Bar, 2-(l) Bolts, 2-(m) Nuts Parts you will need for a 4ft: 1-(j1) Left Back Bar and1-(j2) Right Back Bar, 2-(l) Bolts, 2-(m) Nuts Be sure that the tabs on the (j1) Left Back Bar and (j2) Right Back Bar are facing inward. Refer to figure E1.
Figure F2: Attaching the Projection Bars to Front Bar Step 8:Installing theShroud (Hood Cover) to the Surface Parts you will need for a 3ft: 1 -(n) Shroud (Hood Cover), 4-(o) M8 or M6 Anchors, 4-(m) Nuts, Drill, Level, Measuring Tape Parts you will need for a 4ft: 1 -(n) Shroud (Hood Cover), 4-(o) M8 or M6 Anchors, 2-(m) Nuts, Drill, Level, Measuring Tape a) Carefully measure the distance between each mounting opening on the (n) Shroud (Hood Cover) with measuring tape.
Figure G2: Installing (n) Shroud (Hood Cover) to the Pilot Holes Step 9:Mounting the Back Bars of the Assembled Awning to the Surface Parts you will need for a 3ft: 4-(o) M8 or M6 Anchors, 4-(m) nuts, Drill Parts you will need for a 4ft: 4-(o) M8 or M6 Anchors, 4-(m) nuts, Drill Page | 12
a) Drill the pilot holes into the desired surface. Put the (o) anchors into the wall and make sure they are snug. b) Mount the tabs of the (j1) Left Back Bar and the (j2) Right Back Bar onto each (o) anchor. Make sure the anchor is in between the back bar mounting opening. c) The awning should fit under the (n) Shroud (Hood Cover) d) Place each (m) Nut on the tip of each (o) anchor and tighten accordingly. Please refer to Figures H1.
Step 10:Your Houstonian is complete! Page | 14
WARRANTY 5-Year Manufacturer's Limited Warranty Obtaining necessary permits is the sole responsibility of the purchaser. Purchaser/customer agrees he/she/company will NOT hold Awntech liable for improper installation, maintenance and repairs. A. WARRANTY: 5 Year Limited Manufacturer’s Warranty (Prorated by the month) B. WHO GIVES THIS WARRANTY? Awntech Corporation, 10950 S. Pipeline Road, Euless, TX 76040 C.
•Any failure or damage of the components that results from any intentional or negligent actions by the purchaser or by any other person is not covered by this Warranty. •It is the responsibility of the purchaser to securely fasten the awning to studs, joists, headers or other structural members. Any failure or damage that results from the awning falling from its installed position is not covered by this Warranty.
RETURNS & DAMAGES RETURN QUALIFICATION: You can only return a product if it is defective upon arrival. If you simply do not like the product or if you did not measure correctly, you will only be qualified for a merchandise credit and you will be required to pay for shipping the product back to Awntech in re-stockable condition. There will be a 25% restock fee applicable.