Contents Safety Instructions Information regarding general road safety 95 Arrangement of controls 96 Anti-theft device 97 Entering the code number Entering the Telephone PIN Removing the portable panel Attaching the portable panel General Operation Switching on the unit Adjusting the volume Activating the tone control menu Adjusting the bass Adjusting the treble Fader Adjusting the balance Linear adjustment Loudness on or off Adjust volume of subwoofer or centre speaker Triggering reset Navigation o
Contents Setting voice output Setting the vocal announcement of traffic reports Settings Selecting the units Influencing the calculation of ETA Telephone mode Activate telephone mode Calling up the Communications menu Calling Dial the number Terminating a call Accepting a call Rejecting a call During a call Toggling – second call Conference Telephone book Calling up the telephone book Dialling a telephone book entry Editing / Adding / Deleting telephone book entries Call list Saving entry from call list De
Contents Calling up/ Storing FM stations Calling up/storing MW, LW, SW stations Manual FM tuning Manual tuning MW, LW, SW Regionalisation Turning Regionalisation on or off Turning frequency display on or off Switching radio text display on / off Traffic Programme (TP) Activating/quitting the TP menu Turning TP on or off Selecting automatic tracking Selecting / deleting direct programming Switching mute function on or off Interrupting TP announcements TP announcement volume Display for TMC stations CD, MP3,
GSafety Instructions Operation of the unit is permitted only if traffic conditions are suitable and you are absolutely sure that you, your passengers or other motorists are not endangered, obstructed or inconvenienced. In all cases, all applicable road traffic regulations must be obeyed. Destinations may only be entered when the vehicle is stationary. The country-specific regulations apply for telephone operations. The navigation system is intended to serve as a navigation aid only.
Information regarding general road safety This car radio device is intended and approved for installation and operation in passenger cars, commercial vehicles and buses (vehicle classes M, N and O) whose electric system has a rated voltage of 12V. Installation and maintenance should only be carried out by specialists. Faulty installation or maintenance can result in the malfunctioning of the motor vehicle’s electronic systems. The vehicle manufacturer’s safety instructions must be observed.
Arrangement of controls 1 2 3 4 5 Left rotary control (Info) On / off switch ( ) TP (Traffic programme) key ( ) Communications key ( ) Source key CD ( ) Arrangement of controls 96 6 7 8 9 10 11 Source key Radio ( ) Select navigation ( ) CD eject button ( ) Right Rotary Control (OK) Multifunction keys Display
Anti-theft device Anti-theft device Entering the code number If the auto radio is disconnected from the electrical supply source, the anti-theft device prevents it from being reconnected. After turning on the unit via the button, the prompt Enter Key , is displayed. In an incorrect code number is entered, the prompt Enter key will be displayed once again. If an incorrect code number is entered three times in a row, the unit will display Wait , and it will be blocked for approximately 60 minutes.
Anti-theft device The PIN number does not have to be entered immediately. By pressing one of the source keys , and , you can select one of the available audio sources. No telephone-related functions, however, are available in such a case. This condition is indicated by on the display. To enter the PIN number, first, you need to press the source key . A new request for the PIN number appears.
General Operation General Operation Switching on the unit Activating the tone control menu Adjusting the bass Press button. Additional options for switching on / off: Via ignition. In order to switch on via the ignition, the unit must have been switched off previously via the ignition. After switching off the ignition, the unit can be prevented from switching off by pressing the button within 3 seconds.
General operation Fader Linear adjustment Press the source key for more than 2 seconds. Press multifunction button . Press the source key for more than 2 seconds. Use the right rotary control setting. flat Press the source key for more than 2 seconds. Press multifunction button . Adjusting the balance Press multifunction button briefly - Tone will appear. By pressing multifunction button once again, the tone adjustments for the current signal source (i.e. FM) will be reset to mid-level.
Using Navigation Navigation operation What is navigation? Navigation CDs The term ”navigation” (lat. navigare = to travel by sea) is generally understood to mean the determination of a vehicle’s location, the determination of its direction and its distance from the desired destination and the required route. As navigation aids, stars, prominent landmarks, compass and satellites are used. With OnlinePro, location is determined with the GPS receiver (GPS = Global Positioning System).
Using Navigation For example, if you wish to navigate from a town on the Southern Europe CD (D) to a town on the Northern Europe CD (B), enter your destination address as usual. After entering the town, you will be prompted to insert navigation CD No. 1 by the display Please insert navigation CD #1 . After inserting the relevant CD, enter the road and, if required, the house number or the town centre. The required map data is loaded and stored internally after route calculation has started.
Using Navigation • By briefly pressing the left rotary control , additional information can be requested during route guidance or the current position can be requested when route guidance is not active. See ”Information during route guidance” on page 119 and ”Information during non-active route guidance” on page 121. • The current navigation announcement is interrupted by pressing the left rotary control .
Using Navigation • • P.O.I. Destination Selecting country Menu for selecting regional and interregional destinations of special interest and local points of interest. Points of interest include petrol stations, airports or hospitals, for example. See ”P.O.I.” on page 121. I Select the main Navigation menu with the right Destination and press the rotary control control to confirm.
Using Navigation Entering destination The programme will return to the destination entry. Entering destination town postal code If an incomplete location entry was confirmed, the location selection list is displayed. Select the letters one after the other by turning the right rotary control and press the control to confirm. The selected letter appears enlarged at the right of the display. Use the multifunction button to delete the last confirmed letter.
Using Navigation Entering destination street Select Road: with the right rotary control and press the control to confirm. If the Road entry is not available, no streets are selectable in the selected town. If you select Centre , the programme switches to the town centre. Select the letters in sequence by turning the right rotary control and press the control to confirm. The selected letter appears enlarged at the right of the display. Use multifunction button , to delete the last confirmed letter.
Using Navigation Select the letters one after the other by turning the right rotary control and press the control to confirm. The selected letter appears enlarged at the right of the display. Use multifunction button to delete the last confirmed letter. The complete entry can be deleted by pressing multifunction button for more than 2 seconds. Already entered letters are displayed inversely. For your help, the centre most similar to the entry so far is displayed.
Using Navigation shown in parentheses. If the street number entered is available, the programme returns to the Destination Entry menu. If the street number entered is not available, the street number range list is displayed. A street number range can now be selected. Select Start... to start route calculation. Note: Due to system configurations, route guidance will only be given up to the range of the entered street number.
Using Navigation options can be combined freely. • • Fast route With this setting, the shortest possible travel time to the destination is calculated. • The route is calculated taking into account the traffic announcements received. • Dyn. route TDS TDS is an additional dynamic navigation option. At the time of going to press, this function was still undergoing the release/certification process. You will be notified separately once this process has been completed.
Using Navigation Storing a destination in the destination memory Select Save detination in the Destination Entry menu and press the right rotary control to confirm. In some menus, the destination memory can also be called up for storage of a new destination by pressing multifunction button . A selection from Update entry or press and hold the right rotary control for more than 2 seconds and the destination will be processed without entering a name.
Using Navigation Sorting destination memory Select destination memory (see page 109). Renaming a destination in the destination memory Destination memory full Select destination memory (see page 109). Select the destination to be sorted with the right rotary control and press the left rotary control to display the additional information on the stored destination. Press multifunction button . The selected destination can now be filed into any position desired by turning the right rotary control .
Using Navigation Accessing @ Destinations You can use the @ Destinations menu item in the main navigation menu to download and navigate to destinations you have saved on the BeckerClub homepage. Please see ”BeckerClub” on page 154 for a description of how to access the BeckerClub. In the Main Navigation Menu, select @ Destinations with the right rotary control and press the control to confirm.
Using Navigation @ Route Mode Last destinations By selecting Activate @ route mode and pressing the right rotary control route calculation to the destinations loaded from the homepage is started automatically. Once you have reached the first destination, route calculation to the next destination is started automatically. A list of the last 50 destinations is displayed. Stopovers are not stored as last destinations.
Using Navigation By pressing multifunction button ed entry can be deleted. , the select- With the right rotary control select either Yes or No . The selected element will be displayed inverted . Confirm your selection by pressing the right rotary control . Selecting Yes will delete the entry. Afterward the programme will return to the list of last destinations. Selecting No will return you to the list of last destinations without change.
Using Navigation • Stopover • Entering a stopover Deleting a stopover @ destinations (see page 112) for selection of one of the downloaded destinations as an intermediate destination. Stopover offers the possibility of entering a stopover destination during the active route guidance. Coordinates (see page 114) enables entry of a stopover via geographic coordinates. Press multifunction button . Start route guidance to stopover Press multifunction button .
Using Navigation Delete block Traffic jam function Cancelling route guidance This function allows you to block route sections ahead from the nearest junction and to calculate a detour route when a traffic jam or road block is directly ahead. Entering length of traffic jam Press multifunction button . Using the right rotary control , select the length of the traffic jam and press the control to confirm. is displayed inversely and the route is recalculated. 116 Press Press multifunction button .
Using Navigation Notes on route guidance After entering the destination (address), the system calculates the route and announces: ”Ready to drive off”. You will receive the navigation recommendations by voice messages and screen displays. Press the left rotary control to have the current recommendation repeated. GDanger Accident hazard For clarification, the following contains some examples of possible driving recommendations: • ”Prepare to turn left” or ”Please merge into left lane”.
Using Navigation • ”Please follow the arrows”. Dynamic Route Guidance Note: Dynamic route guidance is not possible in all countries. This display tells you that you are currently on a non-digitised street (i.e. parking lot, garage, parking deck) which is not contained in the digitised road map. The arrow indicates the direction of the destination as the crow flies. • ”Keep right after 2 kilometres”.
Using Navigation Information during route guidance Requesting journey duration and kilometres travelled Displaying/changing route settings During route guidance, press the left rotary control . Press the left rotary control . The destination, the distance and the estimated time of arrival are displayed. The complete list can be displayed by turning the right rotary control . During navigation, press the left rotary control Press the multifunction button . Press multifunction button . .
Using Navigation To display the entire text of the traffic announcements, select the desired entry with the right rotary control . The current time is displayed. After 8 seconds, the system returns to the route guidance display. The clock settings can be accessed by pressing and holding the right rotary control . See ”Setting time” on page 124. Return to the route guidance display by pressing the right rotary control or waiting a short time.
Using Navigation Call up route list During route guidance, the planned route can be called up via the route list, and the relevant traffic announcements for the route can be displayed. Press multifunction button Information during non-active route guidance Press the left rotary control . If possible, the current position with location and street is displayed. . The current road and the road names up to the destination are displayed. Scroll through the route list by turning the right rotary control .
Using Navigation • Selection National Using the right rotary control , select a category and press the control to confirm. A list of points of interest is displayed or, if there are more than 9 entries in the list, you will be prompted to enter the text. Enter the point of interest and confirm. Confirm the special destination in the displayed list by pressing the right rotary control . The system jumps to the route menu.
Using Navigation Note: A list of possible points of interest is displayed immediately when you press the right rotary control for more than 2 seconds without having selected any letters. • Select: Country/town After selecting the country and the town, the categories and the points of interest are displayed for the given location. • Points of interest via @ P.O.I. A point of interest can be called up from the points of interest stored on the Beckerclub homepage via a WAP connection.
Using Navigation • Measuring untit Setting the language The unit display can be set from metres to yards. • Language The language of the text display and voice announcements can be selected. • Adapt ETA Calculation of the ETA can be influenced. Set and confirm Language in the System Settings menu. Select the language using the right rotary control . The language selection is applied when the control is pressed, and the language is installed.
Using Navigation Setting voice output Here you can set whether the voice output of navigation announcements are mixed with the current audio source, the current audio source is muted during navigation announcements, or whether the volume of the navigation announcements can be set independently of the volume of the current audio source. Select and confirm Voice System Settings menu.
Using Navigation • Turning route-relevant traffic announcements on or off: Activate Traffic announcement update , Warning announcement and Only on route as described above. Settings Selecting the units Set and confirm Settings in the System Settings menu. The entries Announcement ETA and If all entries are active, only the warning announcements relevant for the route will be issued. Exit the traffic announcements Set-up menu by pressing the right rotary control for more than 2 seconds.
Using Navigation Influencing the calculation of ETA • Goods vehicle With this setting the unit adjusts for drivers who may take longer for the planned journey. This setting could be selected, for example, for a slower vehicle or in dense traffic areas. Select and confirm Adapt ETA in the System Settings menu. ETA stands for Estimated Time of Arrival. User-defined Calculation of the ETA can be adapted as required.
Telephone mode Telephone mode Activate telephone mode Dial the number In order to activate the telephone mode, the Communications menu must be called up. If the vehicle ignition has been turned off since the last entry of the telephone PIN number, the PIN number must first be re-entered as described in section ”Entering the Telephone PIN” on page 97. In the upper left corner of the display, the strength of the signal reception is displayed. The more bars are visible, the better the telephone reception.
Telephone mode Terminating a call The call is transferred to the handset by removing the handset from its cradle (optional accessory). The unit will then return to the previously active audio source. Rejecting a call An ongoing call or dialling can be terminated. Toggling – second call To do this, briefly press the right rotary control or the multifunction button in the Call menu. The call or dialling will be terminated.
Telephone mode Telephone book to toggle • Both calls can be ended by pressing the multifunction button . • Pressing the multifunction button ends the call to the current party. The call on hold automatically becomes the active call. • The two calls in the conference call can be separated into two individual calls by pressing the multifunction button . The functions described under ”Toggling – second call” on page 129 are available to you again. • Press the multifunction button between the two calls.
Telephone mode Dialling a telephone book entry Editing / Adding / Deleting telephone book entries Call up telephone book. Call up the telephone book. (and international dialling prefix if necessary). Briefly press the right rotary control to apply the number entered. Next, the name for the new entry must be entered. There are two possibilities for dialling an entry: • By turning the right rotary control . • By repeatedly pushing one of the multifunction buttons .
Telephone mode • Upper / lower case letters With multifunction button , you can choose between upper and lower case letters. Löschen: After selecting Delete , the following menu is shown for safety reasons: Call list By turning the right rotary control , select either or No (the inverted entry is active) and press the control to confirm. Selecting Yes deletes the entry from the telephone book. Selecting No will return to the telephone book without change.
Telephone mode The entries in the list can be selected by turning the right rotary control . By briefly pressing the right rotary control , details on the entry can be displayed. Deleting Telephone List Emergency call All telephone lists can be deleted. Call up the Communications menu. Note: Harman/Becker cannot generally be held liable for the emergency call function.
Telephone mode No SIM card inserted: Press . Then, press one of the multifunction buttons. In all three situations, a prompt will appear before the emergency number is actually dialled. Emergency Call Via GDV Call Centre Making an emergency call In the event of an emergency, you can press and to send an emergency call in Germany to the GDV Online Call Centre (Gesellschaft Deutscher Versicherter).
Telephone mode • Emergency call settings In order to make an emergency call via the emergency call button, some settings must be made in the emergency call settings. To call up the Emergency Call Settings menu within the Communications menu, press the button. With the right rotary control, and press to confirm. select • Enabled , Telephone SIM Number After the number has been dialled, enter your own mobile number. Voice Number After selection, a preset telephone number is displayed.
Telephone mode • Car License Plate Settings After the number has been dialled, enter your vehicle licence number. In the Telephone Settings menu, telephone-specific settings can be made. Enter your vehicle licence number. Entry is the same as for entering a new name for a new telephone book entry (Seite 131). When you have entered the complete licence number, store your entry by pressing and holding the right rotary control .
Telephone mode • • (Automatic Call Answering) When the function is active ( ) incoming calls will be answered after the 3rd ring. Accept call automatic. • Telephone Settings After selection, the serial number of the telephone will be displayed. • Call waiting When the function ( ) is active, an optical and acoustic signal will alert you during an ongoing call that a new call is coming in. The caller hears the telephone ringing. When the function ( ) is inactivated, the caller hears a busy signal.
Telephone mode Automatic selects a network corresponding to your location and the SIM card used. When Manual is selected, a list of available mobile phone networks is displayed following interrogation of the network status. GSM Band Settings In the Telephone Settings menu, select Telephone settings with the right rotary control and press the control to confirm. Turn the right rotary control to select the desired mobile phone network. Press to confirm your selection.
Telephone mode Automatically set PIN Select and confirm Set PIN Settings In the Telephone Settings menu, select PIN setwith the right rotary control and press the control to confirm. tings Select Set PIN autom. or Change PIN by turning the right rotary control firm your selection. • . Press to con- Set PIN autom. The PIN number can be stored; i.e. you will not have to enter the PIN each time the unit is turned on. • Change PIN With this selection, the PIN number can be changed. PIN autom. .
Telephone mode With this selection, all calls will be rerouted when the telephone is turned off. Call Rerouting This function directs calls to your mailbox or to another telephone number depending upon settings. • Rest all This selection cancels all active call rerouting functions. In the Telephone Settings menu, select forwarding with the right rotary control press the control to confirm.
Telephone mode The display will briefly show Wait for net response . All Call Rerouting functions are now turned off. Call Rerouting is now turned on. Blocking phone With this function, the telephone can be turned off. Note: If Call Rerouting was already on, an error message will appear. Selection Off : Call Rerouting that may have been on will now be turned off. The display will briefly show Wait for net response .
SMS messages Text messages (SMS) may be received, answered and written. To ensure proper function, the SMS central network number you received from the provider must be entered at ”Settings” on page 145. In order to receive or send messages, telephone operation must be activated. SMS Messaging Reading messages Call up the Communications menu by pressing the button. The entire message can be scrolled through by turning the right rotary control .
SMS messages Delete message Processing messages Once the sender information has been displayed, continue to turn the right rotary control to display a menu for further processing of the message. After selecting the menu entry Delete can delete the current message. SMS , you Select Answer , Writing messages Delete SMS? , Read out , by turning the right rotary control ing it by pressing it. • , and confirm- Answer You can write and send message to the sender.
SMS messages There are two possibilities: Other entry or formatting possibilities: • Enter the number with the multifunction buttons to . To delete incorrect numbers, turn the right rotary control to the left. To confirm the number entered, briefly press the right rotary control . • Upper/Lower-Case Letters With multifunction button , you can choose between upper and lower case letters. • Turn the right rotary control to the right. The telephone book is called up.
SMS messages Deleting All Messages Settings Call up the Communications menu by pressing the button. You can enter the number for the SMS central network in the SMS Settings menu. To call up the SMS Settings menu, press the button in the Communications menu. Press multifunction button Note: If no number or an incorrect number is entered for the SMS central network, it will not be possible to send the SMS. The number for the SMS central network can be obtained from your network provider. .
Internet (WAP) Functions With WAP, you can view current information from the Internet. This information is shown in a specific format, depending upon the display capabilities of the unit. Internet (WAP) Functions Note: Internet access may require registration with a network operator or provider. We cannot guarantee the accessibility of WAP pages. Before the first connection, an access profile must be created or activated. Instructions on how to do this can be found in section ”Settings” on page 150.
Internet (WAP) Functions Browser Menu In the Browser Menu, a WAP address can be entered directly, the address entered in the start profile can be called up, favourite pages can be managed and a list of the pages visited can be displayed. Calling up Browser Menu Select from the URL entered last, Edit URL and New URL . by turning the right rotary control firm your selection.
Internet (WAP) Functions Call up Browser-dependent menu In the active Browser menu, press multifunction button . After a short time, the browser-dependent menu will be displayed. Call up/ Add/ Delete Favourites In the active Browser menu, press multifunction button . 148 Call up: By turning the right rotary control , a previously set favourite address can be called up and confirmed by pressing the control. The WAP Browser shows the corresponding page.
Internet (WAP) Functions Pages visited (History) In the active Browser menu, press multifunction button . A list of the last visited WAP addresses will be displayed. By turning the right rotary control , one of the addresses can be selected and confirmed by pressing. The WAP Browser will display the corresponding page. Saving entry as Favourite: By turning the right rotary control , select Als Favorit speichern and press the control to confirm. A list of the addresses stored in History will be displayed.
Internet (WAP) Functions Settings The configurable keys will be displayed for about 5 seconds. By pressing one of the keys, the WAP page for which the key was configured will be called up. Call up Configuration To call up one of the pages configured in the Internet, press the key in the Communications menu. With the right rotary control select @WAP configuration and press the control to confirm. In the Browser Settings menu, browser-specific settings can be made.
Internet (WAP) Functions Create new profile To create a new profile, select Create new profile? with the right rotary control and press the control to confirm. For browser-specific settings, select Profilename , Dial-in number , Type of connection , User name , Password , IP adress , IP port , Home page , Timer by turning the right rotary control, and confirm by pressing the control . Note: Your provider can inform you which entries need to be made for the following menu items. Profile name: For the max.
Internet (WAP) Functions IP Address: With the right rotary control select IP adresse and press the control to confirm. A recommendation will be made. This recommendation can be accepted or rejected by pressing Yes or No . If No is selected, the IP address for the new profile can be entered. By pressing and holding the right rotary control, the IP Address is applied. Time-out: With the right rotary control select Timer and press the control to confirm. A recommendation will be made.
Internet (WAP) Functions Loading Access Profiles URL Setting The default access profile is the one for the German mobile telephone network T-D1. If you do not use T-D1, please see ”Create new profile” on page 151 for a description of how to set up a profile for your network provider. You can also upload other access profiles to your unit directly from the BeckerClub: Call up the Communications menu by pressing the button.
Internet (WAP) Functions BeckerClub Access to the BeckerClub is included when you purchase Online Pro. The BeckerClub provides a number of services which you can use online via OnlinePro. These include "Download @ destinations" (see also page 112) and "Load @ POIs" (see also page 123). Other services are also available. Accessing the BeckerClub in OnlinePro Call up the Communications menu by pressing the button. Press the You can visit the BeckerClub at: http://www.beckerclub.
E-mail function and other services E-Mail Function Receiving E-Mail Checking E-Mail E-mail settings Web.de has set up an E-mail mailbox for you. E-Mail can be sent directly to the unit. Using the E-Mail function, you can directly call up an existing E-Mail account. Special settings can be made to the e-mail function in the E-mail Settings menu. In order to send an E-Mail to the unit, the address of the unit must be entered.
E-mail function and other services E-mail home page Here, you can set the WAP start page to be used for the e-mail function. With the right rotary control select E-mail home page and press to confirm. Send access data automatically? or Send access data Manually? Here you can determine whether your access data should be sent automatically when you check your e-mail. With the right rotary control select Send access data automatically? or Send access data Manually? and press to confirm.
E-mail function and other services Service settings URL for …. In the Service Settings menu, special settings can be made for the services. Here, you can set the Internet pages from which settings are to be loaded. To call up the Service Settings menu within the Communications menu, press . Note: The factory-set addresses should not be changed. You will receive a message in case of any necessary updates. In the service settings, select With the BeckerClub right rotary control and press to confirm.
Radio mode Radio mode Switching on radio mode Press button. The last selected waveband is called up. Turn on Radio Menu Mode Press in radio mode. By pressing repeatedly, you can choose between the levels DAS seek quality , DAS seek name , Stations RDS and Stations Fix . (see also page 176).
Radio mode Multifunction button indicates that, by pushing the button, other stations can be displayed and selected. If station names are being misused to send advertisements or messages, this station is indicated with L_1 ... L_Z (L = Local) instead of the abbreviated station name. This prevents constant switching in the lower display line. When a station is selected, it is identified by a star (i.e. L*1 ).
Radio mode Turning PTY display on or off Select radio menu mode. Request: Press multifunction button or . The stored station is requested. Manual FM tuning In the Radio Menu Mode, select the level Stawith multifunction button . tions fix Calling up/storing MW, LW, SW stations With multifunction button , select either PTY (PTY Display On) or Frequency (PTY Display Off). Store: Up to 12 stations can be stored under the station buttons.
Radio mode Regionalisation The RDS diversity function is independent of region. In this mode it is possible that, the RDS diversity function may cause the radio to switch between various regional programmes with differing programme formats. In such a case, the special regional programming must be selected directly. If several regional programmes are transmitted by one station, this can only be seen when the station is selected. Stations with additional regional transmitters are indicated with a star (i.e.
Radio mode Traffic Programme (TP) If an RDS Diversity station broadcasts TP announcements, it is possible to interrupt CD, MP3, CDC/AUX, MW, LW, SW play or the mute mode and to switch to the TP announcements. Moreover, you can listen to one FM station while receiving TP announcements transmitted by another FM station.
Radio mode Selecting / deleting direct programming Activate the TP menu. Selecting: Press multifunction button . Switching mute function on or off • Setting 0 - no increase After selection of a TP or EON transmitter, the mute function can be activated by pressing the button briefly. • Setting +3 - strong increase • Setting +1 - slight increase Display for TMC stations Using the right rotary control , select the desired TP transmitter and press the control to confirm.
CD, MP3 or CDC operation CD, MP3, CDC operation Selecting the audio source Basic display for an MP3 CD in the built-in drive: Provided they are available, the following sources Sound interruptions may occur if the CD is soiled. In order to ensure the highest tone quality, please note the following: • CD (Title of a CD in the built-in drive) • MP3 (MP3 Title of a CD in the built-in drive) • MP3 (MP3 Title of an MMC™) • CDC (CDs and Title of the CD changer unit) if installed may be selected.
CD, MP3 or CDC operation Inserting/Ejecting CDs Skipping a title forward/backward Fast forward/rewind Inserting the CD: Press and briefly hold , the display will fold down and the CD slot becomes visible. Insert the CD into the CD slot with the printed side up. The unit will automatically pull the CD into the unit. Then fold the display up again. The CD will begin to play from the first track. Once the last track is played, the unit will start playing the CD again from the first track.
CD, MP3 or CDC operation Title Repeat Pressing multifunction button turns on the ”Title Repeat.” The prompt Rpt is displayed inversely. Pressing multifunction button once again, deactivates the ”Title Repeat” function. Number of tracks and total playing time Press the button in CD mode. By pressing multifunction button , the total playing time for the current track will be displayed briefly.
CD, MP3 or CDC operation MP3 CD in built-in drive General instructions for MP3 To operate an MP3 CD in the built-in drive, please read the following instructions: The music that can be played in your unit’s MP3 mode is generally copyright-protected under applicable international and national laws. In several countries, it is not permitted to reproduce copyrighted material, not even for personal use, without the express prior consent of the copyright holder.
CD, MP3 or CDC operation Notes on playing MP3 CDs If the files on the MP3 CD are arranged in several folders, the folders will be handled in a manner similar to different CDs in the CD changer. The individual directories can be selected by pressing multifunction buttons and . The number shown in front of Track indicates the current directory. After pressing multifunction button , the artist name and track name are displayed in the format “Artist - Name”.
CD, MP3 or CDC operation real time. Otherwise, the particular features described under ”Creating an MP3 data medium” on page 167 apply. Insertion / removal of a recorded MMC™ Insertion: Briefly press the key, the display will fold down. Remove the display. The opening for inserting the MMC™ can be found in the lower left corner of the now-visible opening. MMC™ is inserted e.g. in the CD slot, the device may be damaged. CD Changer Removal: Briefly press the key, the display will fold down.
CD, MP3 or CDC operation Note: Incorrectly inserted CDs will not be played. Note: To allow for the fastest possible changing of CDs, the magazine should be loaded successively, beginning with Compartment 1. Playing CDs Activate CD changer mode (see ”Selecting the audio source” on page 164). Playback begins with the last CD played, at the track playing before switching off. Loaded CDs can be selected by pressing multifunction buttons and .
User settings User menu Call up / quit User Settings menu After opening the User Settings menu, the following Basic Settings can be set in three menu levels according to your personal preference.
User settings Display setting (Lcd) Display brightness setting (Lum) Setting reception optimisation (M/S) The display setting allows you to select from three different display versions. With this function, the display brightness can be set to the preferred value. To set, call up the General Settings menu. Press multifunction button . With the right rotary control , select between 10 and -10 .
User settings Activating AUX/telephone input (Aux) This can be used to switch on the CD changer AF connections if no CD changer is connected. An external unit (Discman, Walkman, etc.) can then be connected. In addition, the mute function lead for an external telephone can be activated. To set, call up the General Settings menu. By pressing multifunction button , call up the 2nd level of the User menu.
User settings Volume display (Vol) With this function, the volume display can be turned on or off. To set, call up the General Settings menu. Press multifunction button to call up the 2nd level of the General Settings menu. Press multifunction button . With the right rotary control select either Volume Indic. On or Volume Indic. Off .
User settings Calling up reset function (Rst) With this function, the unit can be reset to the factory settings. Parts of the unit can also be reset. To set, call up the General Settings menu. Press multifunction button to call up the 3rd level of the General Settings menu. Press multifunction button twice. The individual entries for which a reset option is available are displayed. By turning the right rotary control , the desired entry can be selected from the list.
General instructions General instructions RDS SYSTEM RDS Stations level L music This car radio is capable of receiving RDS signals (RDS = Radio Data System) on the VHF bands. RDS is a technique that enables the transmission of inaudible additional information in the VHF broadcasting range. This means that the broadcaster sends information to be analysed by the auto radio. At the level Stations RDS only identified RDS stations can be stored.
Keyword directory Keyword directory E-Mail Electronic post that can be received or sent via the Internet. GMT Greenwich Meridian Time International time, based on average daylight hours at zero degrees longitude, the basis for the world’s time zones. GPS Global Positioning System System for determinating a vehicle’s location via satellites. GSM Global System for Mobile Communication Standard for mobile communication networks. MMC™ MultiMediaCard™ Memory card for storing data (i.e. music data, etc).
Technical Data • Wavebands: FM 87,5 MHz - 108 MHz MW 531 kHz - 1620 kHz LW 153 kHz - 282 kHz SW 5800 kHz - 6250 kHz • AUX Input: 16 KΩ Input resistance, max. input voltage 1,7 Veff • Frequency range: 20 Hz - 20 kHz for CD operations 30 Hz - 15 kHz for FM 50 Hz - 2,5 kHz for MW, LW, SW • Supply voltage: 12 Volt Technical data • Output : 4 x 18 Watt • Line cross section: 0,75 mm² min. • Loudspeaker impedance: min.
127,&( Dear Listener, In conformance with current EC guidelines, any person may operate this radio receiver. This unit conforms to the current valid European or harmonised national standards. This designation is your guarantee that the unit conforms to the applicable specifications concerning electromagnetic compatibility.