Install Instructions

ManualsBrandsBeckett Pumps ManualsCondensate Removal PumpsHeavy Duty Industrial Condensate Pump, 50 Ft Shutoff (1/5 HP, 115V)

Y8611 Rev. E

AUTOMATIC CONDENSATE UNIT

Keep For Future Reference

INSTALLATION OPERATION

CAUTION: Read rules for Safe Operation and Installation.

*Suffix denotes features

Example: CB25 1 UL HT

Base Model High Temperature Model, for use with

UL Listed maximum 190° F water.

Voltage:

1 = 115V; 2 = 230V: 4 = 460V; 7 = 277V

INTRODUCTION

RULES FOR SAFE OPERATION

1. Carefully read the Owners Manual and rules for safe operation.

2. All wiring must conform to local codes. Use the National Electric Code if local code is nonexistent.

3. CAUTION! To reduce risk of electric shock disconnect from power supply before servicing, pull the plug on models which have

plug-in connections.

4. Do not handle the pump with wet hands or when standing in water as fatal shock could occur. Disconnect main power before

handling unit for ANY REASON!

5. Protect the power cable from coming in contact with sharp objects.

6. Do not kink power cable and never allow the cable to come in contact with oil, grease, hot surfaces or chemicals.

7. Make certain that line voltage conforms to the voltage specified on motor and nameplate.

8. WARNING! To reduce risk of electrical shock, connect only to a properly grounded grounding type receptacle.

INSTALLATION

Select a location for the pump. It should be

as near as possible to the air conditioning

coil. The pump must be level. The inlet

hole must be below the coil drain.

Carefully unpack the pump. Remove the

switch cover. Check each float rod for “free”

action.

CB25

CB50

Owners Manual

BECKETT CORPORATION

Irving, Texas

www. beckettpumps.com

Phone: 972-871-8000

Toll Free: 1-888-BECKETT

Fax: 972-871-8888

Model: CB50*

48’ LIFT

Model: CB25*

23’ LIFT

COVER

PRIMARY SWITCH

TERMINAL BLOCK

FLOAT

TANK

STAND

OUTLET

INLET

MOTOR

SAFETY SWITCH

Summary of content (6 pages)

PAGE 1
Owners Manual AUTOMATIC CONDENSATE UNIT Keep For Future Reference INSTALLATION OPERATION CAUTION: Read rules for Safe Operation and Installation. Model: CB50* 48’ LIFT *Suffix denotes features Example: CB25 1 UL HT Model: CB25* 23’ LIFT Base Model UL Listed High Temperature Model, for use with maximum 190° F water. Voltage: 1 = 115V; 2 = 230V: 4 = 460V; 7 = 277V INTRODUCTION RULES FOR SAFE OPERATION 1. 2. 3. 4. 5. 6. 7. 8. Carefully read the Owners Manual and rules for safe operation.
PAGE 2
PIPING Copper Tube Run a drain line from the evaporator coil drain to the Nut pump. Use the flexible plastic pipe where the code permits. Insert the pipe 1” below the pump cover. Do not install inlet drain line that would interfere with operation Check Valve of floats. Connect outlet tubing (copper or vinyl) to discharge on pump. Do not run tubing vertical more than is recommended by the lift on each unit. For good flow, Ball-Cage slant the horizontal run downward toward the drain.
PAGE 3
Manuel du propriétaire POMPE À CONDENSATS AUTOMATIQUE À conserver pour référence ultérieure OPÉRATION D'INSTALLATION ATTENTION! Lire attentivement les directives pour s’assurer d’un fonctionnement et d’une installation sécuritaires. N° de modèle CB25* ÉLÉVATION DE 7.01 M N° de modèle CB50* ÉLÉVATION DE 14.
PAGE 4
TUYAUTERIE Cuivre Tube Installer une tuyauterie de purge reliant l’évaporateur à la pompe. Utiliser un tube de plastique flexible là où la Noix réglementation le permet. Insérer le tube 2,5 cm (1 po) sous le couvercle de la pompe. Ne pas installer une Anneau tuyauterie d’évacuation à l’entrée qui nuirait au Intérieur fonctionnement des flotteurs. Raccorder le tube ou le Clapet Anti-retour tuyau de sortie (cuivre ou vinyle) à l’évacuation de la pompe.
PAGE 5
Manual del usuario BOMBA AUTOMÁTICA DE CONDENSADO Guarde este manual como futura referencia INSTALACIÓN Y OPERACIÓN PRECAUCIÓN: Lea cuidadosamente todas las instrucciones para una instalación y operación segura. Modelo: CB50* 14.63 M Levantamiento *El sufijo denota ciertas características Modelo: CB25* Por ejemplo: CB25 1 UL HT 7.01 M Levantamiento Modelo básico Voltaje: 1 = 115V; 2 = 230V; 4 = 460V; 7 = 277V Modelos de alta temperatura, para usarse con agua con una máxima temperatura de 87° C.
PAGE 6
TUBERÍA Instale una línea de drenaje desde el drenaje del serpentín del evaporado hasta la bomba. Donde los códigos lo permitan, use tubería de plástico flexible. Inserte el tubo una pulgada debajo de la cubierta de la bomba. No instale una línea de drenaje de entrada que pueda interferir con la operación de los flotadores. Conecte la tubería de desagüe (ya sea de cobre o de vinilo) al tubo de descarga de la bomba.