Instructions / Assembly

ManualsBrandsBeckett ManualsOutdoorsStanding Bear Fountain

STEP 1:

Place the Basin on a level, water tolerant surface, away from falling leaves.

PASO 1: Coloque el Base en un riegue la superficie tolerante, lejos de caerse hojas.

STEP 2: Place the Pump into the Fountain, and route the Pump cord through the Fountain’s Cord Exit Notch.

PASO 2: Sitúe la Bomba dentro de la Fuente y que el cordón de la Bomba esté dirigido a través de la Muesca de Salida de la Fuente.

STEP 3: Set the Pump’s flow control to max (+). Attach the Fountain’s tubing to the discharge of the Pump.

PASO 3: Fije el flujo del agua de la Bomba al Máximo (+). Conecte la Manguera de la Fuente a la Bomba.

STEP 4: Connect the Light Cord to the Pump cord 1 and the Pump Cord 2 to the Transformer.

PASO 4: Conecta la conexión de la luz con la conexión 1 de la bomba y conexión 2 de la bomba con la transformador.

STEP 5: Fill the Basin with water. Do not allow the Pump to run dry!

PASO 5: Llene el Base de agua. ¡No permita que la Bomba funcione seca!

STEP 6: Plug the PUMP electrical cord into a properly grounded GFCI outlet.

PASO 6: Conecte el cordón eléctrico de la BOMBA a una salida con tomacorriente a tierra.

STEP 7: To adjust the Fountain’s flow rate, unplug the

Pump electrical cord from the outlet and adjust the

Pump’s flow control. Repeat above steps until you

achieve the desired flow.

PASO 7: Si decide ajustar el flujo del agua en la fuente,

desconecte el cordón eléctrico de la Bomba, y ajuste el

control del agua en la Bomba hasta lograr el flujo deseado.

Pump

Bomba

Transformer

Transformador

MODEL: 7223210

Standing Bear

Fountain

Fuente de Oso parado

NOTES:

• Choose an appropriate location for your

fountain.

• While Beckett’s fountains are designed to

operate as splash free as possible, some

water splashing out of the fountain is

inevitable. Place your fountain in a location

where any splashing will not cause damage.

• Keep your fountain full of water and clear of

dirt to ensure proper functioning of the pump.

NOTAS:



Escoja un lugar apropiado para su fuente.



Aunque las fuentes de Beckett están

diseñadas para operar sin que salpique el

agua, va a ser inevitable que el agua

salpique un poco alrededor de la fuente.

Ponga su fuente en un lugar que no cause

daños si el agua salpica.



Mantenga su fuente llena de agua y limpia

de residuos y mugre para asegurar un

adecuado funcionamiento de la bomba.

INSTRUCTIONS

INSTRUCCIONES

Fountain

Fuente

Pump Cord 2

Conexión 2

Light Cord

Cordón de la luz

Pump Cord 1

Conexión 1

Summary of content (2 pages)

PAGE 1
INSTRUCTIONS INSTRUCCIONES Standing Bear Fountain Fuente de Oso parado MODEL: 7223210 NOTES: • • • Choose an appropriate location for your fountain. While Beckett’s fountains are designed to operate as splash free as possible, some water splashing out of the fountain is inevitable. Place your fountain in a location where any splashing will not cause damage. Keep your fountain full of water and clear of dirt to ensure proper functioning of the pump.
PAGE 2
TROUBLE SHOOTING - LOCALIZACIÓN DE FALLAS If your FOUNTAIN PUMP fails to operate: • Check the circuit breaker and try another outlet to verify that power is supplied to the Pump. • Check the water level in the Fountain. The Pump requires a minimum water depth of 2” to operate properly. Running the Pump without sufficient water can damage the pump. • Check the setting of the Flow Control on the Pump. Check the Pump Discharge and Intake Tube for dirt and debris. Clean if necessary.