Installation Manual

ManualsBrandsBedrug ManualsAutomotiveBedRug BedTred Ultra Full Bedliner UTQ17SBK fits 17+ SUPERDUTY 6.75'

Preparation

BedTred Truck Bed Liner Installation Instructions

Part Number(s): Multiple

WARNING: IMPROPER

INSTALLATION WILL RESULT IN

LINER FLYING OUT OF THE TRUCK.

FOLLOW INSTRUCTIONS EXACTLY

IMPORTANT: Read all instructions before

beginning installation. Be sure to dispose of

all adhesive backing tape in the trash.

Kit Contents

Additional Items Required for Installation

Recommended Tools

Personal and Vehicle

Protection

Safety Glasses

Gloves

Special Tools

Various

Installation Tools

Utility Knife

Scissors

Awl

Special Chemicals

Approved Cleaner

General Applications

Item # Qty Req'd Description

1 1 BedTred Floor w/ Tailgate Panel

2 1 BedTred Bulkhead Panel

3 2 BedTred Sidewall Panels (L&R)

4 1 1"x 63.5" Adhesive Bk. Hook

5 3 1"x 60" Adhesive Bk. Hook

6 25 1"x 2" Adhesive Bk. Hook

7 6 1"x 10" Adhesive Bk. Hook

8 4 1"x 6" Adhesive Bk. Hook

9 1 #4298 Adhesive Promotor Pad

6' roll 2" Non-adhesive Hook

11 1

Item # Quantity Req'd Description

Multiple

STOP: Damage to the vehicle may occur. Do

not proceed until process has been completed.

OPERATOR SAFETY: Use caution to avoid

risk of injury.

CAUTION: A process that must be carefully

observed in order to reduce the risk of damage

to the accessory/vehicle and to ensure a quality

installation.

TOOLS & EQUIPMENT: Calls out the specic

tools and equipment recommended for this

process.

Notes:

Tools required to remove

tiedowns (unique to vehicle)

To cut slits or to trim BedTred

for cargo mgmt. system

To cut hook tape to length

To locate holes for cargo hook

attachment bolts (or other

accessories)

70% (or higher) Isopropyl Alcohol

Legend

This document covers such items as:

• Vehicle preparation (use of cleaners,

adhesive promoters, etc.)

• Safety (rechecking torque procedure, etc.)

• BedTred installation

1. Check Kit Contents

— Verify that your kit contains all the

parts listed in the Kit Contents.

— Test fit all parts in truck bed prior to

installation to determine correct location

for best appearance.

Bulkhead

Floor Panel

Side

Panels

Tailgate Panel

Printed Set of Instructions

10 1

ULTRA

UTINST Rev. 1 7/27/2016

Page 1 of 6

Summary of content (6 pages)

PAGE 1
ULTRA Preparation Part Number(s): Multiple Kit Contents Item # Qty Req'd 1 1 2 1 3 2 4 1 5 3 6 25 7 6 8 4 9 1 10 1 11 1 Description BedTred Floor w/ Tailgate Panel BedTred Bulkhead Panel BedTred Sidewall Panels (L&R) 1"x 63.5" Adhesive Bk. Hook 1"x 60" Adhesive Bk. Hook 1"x 2" Adhesive Bk. Hook 1"x 10" Adhesive Bk. Hook 1"x 6" Adhesive Bk.
PAGE 2
ULTRA Procedure BedTred Truck Bed Liner Installation Instructions 2. Vehicle Preparation a. Wash and Dry the bed and tailgate area thoroughly before proceeding. b. Remove bolt-in type cargo hooks or load extenders (if equipped) Cargo hooks will be reinstalled in Step 8. IMPORTANT: Truck bed should be at least 68°F (20°C) for maximum adhesion. Clean all areas with 70% (or higher) Isopropyl Alcohol before applying tape. Do not remove backing from any tape until ready to adhere to the truck bed.
PAGE 3
ULTRA Procedure BedTred Truck Bed Liner Installation Instructions 5. Zip the BedTred truck bed panels together From the back (loop side) of the panels, zip the two side panels to the Floor Panel (starting at the back of the BedTred) and then zip the Bulkhead Panel to the Floor Panel. 6. Place the joined BedTred panels in truck Turn the BedTred over again and place it carefully into the truck bed. Position the Floor Panel carefully. 7. Attach Bulkhead Panel to Truck Bed.
PAGE 4
ULTRA BedTred Truck Bed Liner Installation Instructions Procedure 9. Attach sidewall panels to truck bed. Begin by attaching the front edge of the side panel to the Bulkhead Panel. Be sure the 2" wide hook is secure against the fabric side of the side panel. It is best to center and attach the wheel well area next. Clean attachment areas of bed with alcohol and let dry. Remove backing tapes and adhere to truck. Work from the bottom up then toward the front and rear. Repeat with the opposite sides.
PAGE 5
ULTRA Procedure BedTred Truck Bed Liner Installation Instructions Clean hook attachment areas on sheetmetal with alcohol and let dry. Place Tailgate Panel in proper location. Remove backing tape and attach bottom 1" x 60" fastener. Press firmly in place. Remove backing tape and attach top 1"x 60" fastener to truck tailgate. Press firmly in place. You have now completed installation of your BedTred Ultra Bed Liner. UTINST Rev.
PAGE 6
ULTRA Care and Warranty BedTred Truck Bed Liner Installation Instructions BedTred® CLEANING INSTRUCTIONS The mildew resistant BedTred foam will not absorb liquids. The engineered polypropylene fiber surfaces resist stains and deterioration from most acids, chemicals, gasoline and oils, etc. Therefore, by following the cleaning instructions below, your BedTred will remain serviceable for as long as you own your truck. Cleaning your BedTred is easy: 1.