BIGG BUGG BB722AA, BB722BA, BB722GA Assembly and Operating Instructions FOR OUTDOOR USE ONLY AUSTRALIA / NEW ZEALAND
CONGRATULATIONS CONTENTS Dear customer, Important safety instructions........................................................3 Congratulations and thank you for choosing our barbecue. We are sure you will find it a pleasure to use. Before you use the barbecue, we recommend that you read through the relevant sections of this manual, which provide a description of your appliance and its functions. Product description.......................................................................
IMPORTANT SAFETY INSTRUCTIONS Please read the user manual carefully and store in a handy place for later reference. WARNING WARNING • Do not lean over barbecue when lighting. TIPS & INFORMATION IMPORTANT • Do not leave the barbecue unattended when alight. Important – check for any damages or marks • Do not delay lighting once the gas has been turned on.
PRODUCT DESCRIPTION 3 2 10 12 11 7 4 1 6 5 9 8 1 Barbecue body 2 Hood 3 Hood handle/thermometer 4 Control knob 5 Grease tray 6 Shelf 7 Utility hook 8 Condiment tray 9 Trolley assembly 10 Plate 13 11 Grill 12 Burner 13 Barbecue lock handle 14 Cylinder hook 4 PRODUCT DESCRIPTION 14
DIMENSIONS 795mm 656mm 1075mm 855mm 678mm 885mm 636mm 1318mm 221mm WARNING CAUTION When installing the barbecue ensure there is sufficient clearance behind barbecue for hood to open fully.
PARTS DESCRIPTION QTY DESCRIPTION QTY Barbecue body and hood assembly 1 Cylinder shield 1 Left hand side leg 1 Condiment tray 1 Right hand side leg 1 Grill 1 Connecting panel assembly 1 Plate 1 Front panel 1 Grease collection tray 1 Wire shelf 1 Shelf 2 Wheel and hub caps 2 Fasteners Pack Wheel Axle - 2pcs Allen Key - 2pcs Screw G14x15 - 13pcs Circlip - 2pcs 6 PARTS Screw G14x15 - 13pcs 1 plastic bag containing: • Instruction manual • Match holder for manual ignition •
ASSEMBLING THE BARBECUE Tools required for assembly This manual must remain with the owner for future reference. • Allen Key (supplied) • Pliers (not included) 1. Assemble left hand leg to top connecting panel. Qty. 5 Screw G14, 15mm (black) 2. Assemble right hand leg to top connecting panel. Qty.
ASSEMBLING THE BARBECUE 3. Assemble front panel to top connecting panel. Qty. 2 Screw G14, 15mm (black) 4. Assemble Condiment Tray between legs as shown.
ASSEMBLING THE BARBECUE 5. Assemble wire shelf to leg (do not tighten screws until wheel axle shaft is installed at step 7). Qty. 4 Screw G14, 15mm (black) 6. Assemble wire shelf to leg with screws. Qty.
ASSEMBLING THE BARBECUE 7. Assemble the wheels to axle with circlips (pliers may be required to assemble circlip onto axle). Qty. 2 Axle wheel Qty. 2 Circlip 8. Assemble cylinder shield panel. Qty. 6 Screw G14, 15mm (black) Cylinder shield Screw locations x 6 9. Insert cylinder hook.
ASSEMBLING THE BARBECUE 10. Assemble barbecue body and hood assembly onto the stand and lock as shown. For ease of installation it is recommended for two people to do this. 1 2 3 WARNING WARNING Do not operate the barbecue when separated from the trolley (ie. bench mounted) barbecue should only be separated from trolley for easy transportation.
GAS SPECIFICATIONS GAS BOTTLE SAFETY AND LEAK TESTING GAS TYPE UNIVERSAL LPG NATURAL GAS Gas bottle installation Maximum gas consumption 32 MJ/h 33 MJ/h • Connect the gas hose to the gas bottle. Injector office diameter 1.10 mm 1.83 mm • Place the gas bottle onto the cylinder hook at the rear of the barbecue. Number of injectors 2 2 Regulator pressure 2.75 kPa 1.00 kPa NOTES: • This appliance MUST be serviced only by a qualified licensed person.
NATURAL GAS CONVERSION Natural gas installation NOTE: Conversion of this unit to natural gas must be carried out by a qualified licensed person and a Certificate of Compliance must be issued to the owner on completion of the installation and conversion. Converting the unit to natural gas This barbecue is supplied set up for Universal LPG and is labelled accordingly. A natural gas conversion kit is available as an accessory by contacting Electrolux Customer Service Centre.
NATURAL GAS CONVERSION 3. Attach clip on aeration shutter to each burner as shown: Aeration shutter 4. Refit burners ensuring the injector is located inside the burner inlet. 5. Remove LPG hose and regulator assembly and replace with natural gas hose and regulator assembly 6. Replace the ULPG gas type label with the natural gas label supplied. 7. Leak test using same procedure for ULPG, as detailed on page 12 (leak test points shown below). 8.
NATURAL GAS CONVERSION INSTALLATION WARNINGS 9. Turn down adjustment When converting to natural gas the turndown setting will need to be adjusted to give a satisfactory flame on low setting. • Remove knobs from valve shafts. • Using a flat bladed screwdriver, turndown adjustment screw should be fully inserted and then rotated ¾ turn counter clockwise. • Repeat for other valve. • Following of the gas and leak testing as per previous steps, light both burners and set to high.
CONFIGURATION OPTIONS TIPS & INFORMATION IMPORTANT Plate and grill can be positioned either on the left or right side as shown. OPERATING INSTRUCTIONS WARNING WARNING The use of two hotplates is not recommended. This configuration does not allow adequate ventilation for the barbecue to operate safely. INCORRECT Control functions Before lighting the barbecue: • Check that all hoses and gas fittings are tight. • Open the roasting hood. • Check all control knobs are in the ‘OFF’ position.
Preheating • This barbecue is fitted with high power burners.
CLEANING AND CARE Light both burners and set to ‘HIGH’ WARNING WARNING Please ensure that your barbecue is switched off and has cooled down before following the instructions below. After approximately 30 minutes, this should turn any baked on food or grease to ash. Once the surface has cooled, the residual ash can be wiped clean with a damp cloth. Cast iron plates and grills After cleaning, lightly season the cast plate and cast grills with cooking oil.
TROUBLESHOOTING ACCESSORIES PROBLEM POSSIBLE CAUSE SOLUTION STANDARD INCLUSIONS Barbecue won’t light No gas Check isolation valve is ON Cast iron hotplate Gas bottle empty – refill or change gas bottle Ignition system not working Check spark being generated when knob rotated Cast iron grill OPTIONAL EXTRAS* Gas conversion kit – NG Cast iron planchar plate Weatherproof cover Ignition electrode wet or dirty, gently clean and dry electrode, ensuring position unchanged Manually light the barbecue
NOTES 20 NOTES
NOTES 21
NOTES 22 NOTES
Warranty FOR SALES IN AUSTRALIA AND NEW ZEALAND APPLIANCE: BEEFEATER BUGG BARBECUE This document sets out the terms and conditions of the product warranties for Electrolux Appliances. It is an important document. Please keep it with your proof of purchase documents in a safe place for future reference should there be a manufacturing defect in your Appliance. This warranty is in addition to other rights you may have under the Australian Consumer Law. 1.
For more information on all Beefeater products, or for dimension and installation information, call into your retailer, phone or email our customer care team or visit our website: AUSTRALIA phone: 1300 307 939 fax: 1800 356 669 email: customercare@electrolux.com.au web: beefeaterbbq.com NEW ZEALAND phone: 0800 436 245 fax: 0800 225 088 email: customercare@electrolux.co.nz web: beefeaterbbq.com Beefeater. We are part of the Electrolux Family.
