Datasheet

Beha-Amprobe
®
Division of Fluke Corp. (USA)
c/o Fluke Europe BV
In den Engematten 14
79286 Glottertal, Germany
Tel. [phone] - 8009-0
[e-mail]
beha-amprobe.de
52 Hurricane Way
NR6 6 JB United Kingdom
e-mail: [e-mail]
beha-amprobe.com
Science Park Eindhoven
5110 NL-5692 EC Son
The Netherlands
Tel. [phone]
beha-amprobe.com
©2019 Beha-Amprobe
®
6011266 A-eng
beha-amprobe.com
EV-500 Series
Test Adapter Kits for Electric
Vehicle Charging Stations
Get access to the socket-outlets of a charging station to perform safety and
functional tests, while simulate presence of an electrical vehicle
The EV-500 Series Test Adapter Kits are designed to test function and safety of charging stations
mode 3 for AC charging. The Adapter Kit allows you to conduct tests in combination with
appropriate test instruments like an installation tester (for example the Beha-Amprobe ProInstall
Series) and/or Scope Meters (oscilloscope) (for example Fluke 120B Series Industrial ScopeMeter
handheld oscilloscopes). With the Adapter Kit, the charging stations can be tested in accordance
with IEC/EN 61851-1 and IEC/HD 60364-7-722.
EV-500 Series
Test Adapter Kits
Proximity Pilot (PP)
state selector
Control Pilot (CP)
state selector
EVC-20 test cable for type 2
with socket outlet or xed cable
with vehicle connector
PE Pre-Test to check if
possible hazard touch
voltage is present
Measuring terminals
to check safety and
function of charging
station
Error simulation
for “E” and PE
error
Mains socket for external
load to check power meter
Features & Functions
• Suitable to vehicle charging stations with
charging mode 3
• EV-connectors for type 2 and type 1
• PE Pre-Test: With this safety feature the PE conductor
will be tested for possible presence of dangerous
voltage against earth.
• Proximity Pilot (PP) state “Cable Simulation”:
With PP State rotary switch the adapter can simulate
various current capabilities of charging cables.
• Control Pilot (CP) state “Vehicle Simulation”:
With CP State rotary switch selector various charging
states can be simulated.
• Separate phase indication by three LED
lamps for easy check if voltage is present.
• Measuring terminals L1, L2, L3, N and PE
to connect test device like installation tester to
perform safety and functional tests.
• Mains socket offering the possibility
to connect an external load to check if the
electric power meter works and counts in the
right manner.
• Simulation of CP error “E”
• Simulation of PE error (Earth fault)
• Terminals for CP signal output to
check communication between adapter
(=simulated electrical vehicle) and
charging station. This could be measured
by a scopemeter. The voltage level denes the
charging modes and the duty cycle of this PWM
(Pulse Width Modulation) signal denes the
charging current.
• IP 54 rating - Dust and splashing water protected
to connect to
EV charging station:
EVC-20 test cable for type 2
with socket outlet or xed
cable with vehicle connector
Type 2
IEC 62196-2
Optional:
EVC-13 test cable for type 1
with vehicle connector
Type 1
IEC 62196-2/SAE J1772
Safety Certication
All Beha-Amprobe tools, including the Beha-Amprobe EV-500 Series, are rigorously tested
for safety, accuracy, reliability, and ruggedness in our state-of-the-art test lab. In addition,
Beha-Amprobe products that measure electricity are listed by a 3rd party safety lab, either UL or CSA.
This system assures that Beha-Amprobe products meet or exceed safety regulations and will perform
in a tough, professional environment for many years to come.
Terminals for CP signal output to
check communication protocol