TDS
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative,
call 1-800-854-0133 Ext. 2 (U.S.A. only) or visit behr.com. ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
TECHNICAL DATA SHEETTECHNICAL DATA SHEET
Revised 01/2020
1 of 2
DECKPLUS® SOLID COLOR WATERPROOFING WOOD STAIN
NO. 211 WHITE BASE
PRODUCT INFORMATION
BEHR® DECKPLUS® SOLID COLOR WATERPROOFING WOOD STAIN provides protection from water and the sun’s harmful rays
for up to 5 years on decks and 15 years on fences and siding. Available in over 1,600 custom colors and formulated for color
matching, this stain will hide imperfections while allowing the wood texture to show through. The 100% acrylic formula
resists cracking, peeling and blistering. This product is also great for composite decks.
RECOMMENDED USES:
Ideal for properly prepared exterior vertical and horizontal surfaces such as:
• Wood • Engineered (Synthetic) Wood • Wood Composite
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 211 Tintable White 124 oz / 4 oz
No. 213 Deep Base 116 oz / 12 oz
Resin Type: 100% Acrylic
Weight per Gallon: 10.4 lb
% Solids by Volume: 38% ± 2%
% Solids by Weight: 50% ± 2%
VOC: <100 g/L
Flash Point: N/A
Viscosity: 68-77 KU
Recommended Film Thickness:
1st Coat: Wet: 5.4 mils / Dry: 2.0 mils @ 300 sq ft/gal
2nd Coat: Wet: 2.7 mils / Dry: 1.0 mils @ 600 sq ft/gal
Coverage: 200-400 sq ft/gal, depending on application
method and substrate porosity.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8"-1/2" nap roller cover, depending on surface
texture
Airless Spray:
Tip: .015"- .019"
Filter: 60 mesh
Fluid Pressure: 1,400 – 2,400 psi
Follow spraying immediately with back brushing or back
rolling for a uniform appearance
Thinning: If thinning is required, thin with water at a rate
of no more than 1/2 pint per gallon.
Dry Time: @ 77°F & 50% RH
To Recoat: 1-2 hours
Light Foot Trac: 24-48 hours
Full Cure: 72 hours
Dry times are temperature, humidity, and lm thickness
dependent.
SURFACE PREPARATION:
The following steps and products are recommended
for best results: If you use a product such as BEHR
PREMIUM® Wood Stain & Finish Stripper No. 64 to remove
loose wood bers, latex, oil-based and 100% acrylic coating
on new or weathered wood, then you must use a product
such as BEHR PREMIUM® All-In-One Wood Cleaner No. 63
to clean, brighten & neutralize wood. If you do not use
BEHR PREMIUM Wood Stain & Finish Stripper No. 64, then
use a product such as BEHR PREMIUM All-In-One Wood
Cleaner No. 63 to clean and brighten the wood surface and
to remove light to medium exterior stains caused by mold,
mildew, algae & fungus. Rinse thoroughly and allow to
dry before coating. On new wood, use a product such as
BEHR PREMIUM All-In-One Wood Cleaner No. 63 to remove
mill glaze and open the pores of the wood. Lightly sand to
remove remaining wood bers/fuzz.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
SYSTEM RECOMMENDATIONS:
Wood:
• BEHR PREMIUM PLUS® Exterior Multi-Surface Primer &
Sealer No. 436
CLEAN-UP/DISPOSAL:
Clean all tools and equipment with warm, soapy water. Do
not dispose of this product down a drain. If spilled, contain
material and remove with an inert absorbent. Dispose of
contaminated absorbent, container and unused product
in accordance with all current federal, state and local
regulations. For recycling or disposal of empty containers,
unused product and soiled rags, contact your household
refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing
• For best results, apply when air, material and surface
temperatures are between 40°F and 90°F. Avoid applying
stain in direct sunlight or to hot surfaces. Temperatures
above 90°F can cause the paint to dry too fast. Do not
apply if rain is expected within 24 hours of product
application.
• Test product for color on a small hidden area before
proceeding.
• No primer needed on most woods. However, Redwood,
Cedar, Cypress and other “bleeding” woods contain water
soluble extractive that may cause discoloration of white
and pastel colors; therefore, prime the above type woods
with one coat of a product such as BEHR PREMIUM PLUS
Exterior Multi-Surface Primer & Sealer No. 436.
• Avoid applying stain too heavily. Over-application of
DECKPLUS SOLID COLOR WATERPROOFING WOOD STAIN
results in lm forming on the wood surface and therefore
subject to peeling and aking.
• Stained surfaces may become slippery when wet.
• Shelf life under normal conditions is 2 years (unopened
containers).
GENERAL INFORMATION:
WARNING IRRITANT HARMFUL IF SWALLOWED.
CONTAINS: ETHYLENE GLYCOL. MAY CAUSE EYE, NOSE AND
THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES
AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR
EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH
ADEQUATE VENTILATION. To avoid breathing vapors and
spray mist, open windows and doors or use other means to
ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase
fresh air. If properly used, a respirator (NIOSH approved for
organic vapor with P series particulate pre-lter) may oer
COMPLIES WITH THE BELOW AS OF 1/1/2020
SCAQMD YES OTC YES
CARB SCM 2007 YES LADCO YES
CARB YES AIM YES
OTC Phase II YES MPI 16