TDS
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2017 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 2/2017
1 of 1
PRODUCT INFORMATION
BEHR® DECKPLUS™ SEMI-TRANSPARENT WATERPROOFING WOOD STAIN is a 100% acrylic formula which lasts for up to 3
years on decks and 5 years on fences and siding, due to its durability. Choose from 60 dierent colors that add beauty
while allowing the natural wood grain to show through. The stain provides a durable, water-repellent nish that also
protects against the sun’s harmful UV rays. Clean-up is easy with soap and water.
RECOMMENDED USES:
Properly prepared exterior vertical and horizontal surfaces:
• Wood
• Engineered (Synthetic) Wood
• Pressured Treated Lumber
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 3077 Tint Base 128 oz.
Resin Type: 100% Acrylic
Weight per Gallon: 8.6 lbs
% Solids by Volume: 17.6%
% Solids by Weight: 19.8%
VOC: <100 g/L
Flash Point: N/A
Viscosity: 20-45 sec #2 Zahn Cup
Recommended Film Thickness:
Wet: 6.6 Dry: 1.2 mils @ 250 Sq. Ft./Gal.
Wet: 3.3 Dry: 0.6 mils @ 500 Sq. Ft./Gal.
Coverage: 250-500 Sq. Ft./Gal. Apply a thinner second coat
at a spread rate of approximately 500-600 Sq.Ft./Gal. 2 coats
are required for optimal appearance and durability.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8" nap
Pad Applicator
Airless Spray: At packaged consistency
Tip: .015- .019"
Filter: 60 mesh
Dry Time: @ 77° & 50% RH
To Recoat: 1-2 hours
Light Foot Trac: 24-48 hours
Full Cure: 72 hours
• Follow spraying immediately with a pad, back brushing or
back rolling for a uniform appearance.
• Work in small sections lightly saturating the surface and
immediately back-brush or use pad applicator to eliminate
puddling; remove excess and evenly distribute the nish.
Maintain a wet edge when applying.
SURFACE PREPARATION:
The following steps and products are recommended
for best results: If you use a product such as
BEHR PREMIUM® Wood Stain & Finish Stripper No. 64 to
remove loose wood bers, latex, oil-based and 100% acrylic
coatings on new weathered wood, then you must use a
product such as BEHR PREMIUM® All-In-One Wood Cleaner
No. 63 to clean, brighten & neutralize wood. If you do not
use a product such as BEHR PREMIUM Wood Stain & Finish
Stripper No. 64, then use a product such as BEHR PREMIUM
All-In-One Wood Cleaner No. 63 to clean and brighten the
wood surface and to remove light to medium stains caused
by mold, mildew, algae & fungus. Rinse thoroughly and
allow to dry before coating. On new wood, use a product
such as BEHR PREMIUM All-In-One Wood Cleaner No. 63
to remove mill glaze and open the pores of the wood.
Lightly sand to remove remaining wood bers/fuzz.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or log on
to www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with clean water. For proper
disposal of empty containers and unused product, contact
your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing
• Do not use without the addition of tinting colorants
• Do not use if rain is expected within 24 hours
• DO NOT THIN PRODUCT
• Avoid applying stain in direct sunlight or hot surfaces
• Test product for color on a small hidden area
before proceeding
• Over application of stain will lead to surface failure
including peeling & cracking
• Stained surfaces may become slippery when wet.
• Shelf life under normal conditions is two years
(unopened containers)
• Temperature Range: 40-90°F
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Harmful if
swallowed. Wear protective clothing, gloves, eye, and face
protection. Do not eat, drink, or smoke when using this
product. Take o contaminated clothing and wash it
before reuse. Wash hands thoroughly after handling.
Collect spillage and avoid release to the environment.
Dispose of unused, contents, container and other
contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for
several minutes and remove contacts if present and easy
to do. Continue rinsing and get medical attention if eye
irritation persists. If on skin: Wash with plenty of soap
and water. If swallowed: Rinse mouth and get medical
attention if you feel unwell.
DECKPLUS™ SEMI-TRANSPARENT WATERPROOFING WOOD STAIN
NO. 3077
COMPLIES WITH THE BELOW AS OF 2/1/2017
SCAQMD YES OTC Phase II YES
CARB YES LADCO YES
CARB SCM 2007 YES AIM YES
OTC YES