TDS

TECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2017 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
* For details visit behr.com/marqueeguarantee
Revised 1/2017
2 of 2
Stain-Blocking: After priming, test for stain bleed-through
by applying the topcoat to a small section. If the stain
bleeds through the topcoat, apply a second coat of
primer and test again before top-coating the entire
area. If bleeding continues, a longer dry time may be
needed before top-coating.
Masonry: All masonry surfaces must be cured at least
30 days before painting. The pH must be 10.0 or lower
prior to coating. Smooth masonry may require an adequate
prole for adhesion. For all other smooth concrete, create a
prole using a product such as BEHR PREMIUM®
Concrete & Masonry Cleaner & Etcher No. 991 or with
mechanical means. Remove loose aggregate and debris
using a product such as BEHR PREMIUM
Concrete & Masonry Degreaser & Cleaner No. 990.
Ferrous and Non-Ferrous Metal: The oil lm on new
non-ferrous metal must be removed before it is painted.
Remove oil lm with a detergent and water solution.
For better paint adhesion, sand the surface with sandpaper,
steel wool, or by using a product such as BEHR PREMIUM
Concrete & Masonry Cleaner & Etcher No. 991. Clean by
scrubbing the surface with a detergent and water
solution, followed by a thorough rinsing with clean water.
Metal: Remove all rust and mill scale using sandpaper, steel
wool, abrasive blasting, or other abrading methods to create
a prole on the metal’s surface. New Surfaces: Clean the
metal by scrubbing the surface with a detergent and water
solution, followed by a thorough rinsing with clean water.
Bare metal must be primed the same day it is cleaned.
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD or
visit www.epa.gov/lead.
RECOMMENDED PRIMER/SYSTEMS:
PROPERLY PREPARED NEW SURFACES:
Drywall, Plaster, Masonry and Wood:
• 2 coats is the minimum required for new or uncoated
surfaces and surfaces with severe tannin and stains.
Ferrous & Non Ferrous Metals
and Architectural Plastics:
• BEHR PREMIUM PLUS® Interior All-In-One
Primer & Sealer No. 75.
PREVIOUSLY PAINTED SURFACES:
• Use a full coat, or spot prime repaired surfaces with heavy
stains, including tannin, with BEHR MARQUEE®
Interior Paint.
CLEAN UP:
Clean all tools and equipment with clean water.
For disposal of empty containers and unused product,
contact your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Do not use on oors.
• For best results, apply at temperatures between
50°F - 90°F. Temperatures above 90°F may aect the
application such as drying too fast. Avoid painting in
direct sun. NOTE: If the surface is hot to the touch it
should be considered too hot to apply this coating.
• Avoid heavy trac for 24 hours.
• Allow four weeks before washing or cleaning for full cure.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Harmful if
swallowed. Wear protective clothing, gloves, and eye &
face protection. Do not eat, drink, or smoke when using
this product. Take o contaminated clothing and wash
it before reuse. Wash hands thoroughly after handling.
Collect spillage and avoid release to the environment.
Dispose of unused contents, container and other
contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for
several minutes and remove contacts if present and easy
to do. Continue rinsing and get medical attention if eye
irritation persists. If on skin: Wash with plenty of soap
and water. If swallowed: Rinse mouth and get medical
attention if you feel unwell.
INTERIOR EGGSHELL ENAMEL PAINT
NO. 2450 ULTRA PURE WHITE®