TDS
TECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2017 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
*
For details visit behr.com/marqueeguarantee
Revised 1/2017
1 of 2
INTERIOR SEMIGLOSS ENAMEL PAINT
NO. 3450 ULTRA PURE WHITE®
PRODUCT INFORMATION
BEHR MARQUEE ® Interior Semi-Gloss Enamel Paint is our best interior paint with exceptional hide and stain resistance plus an
antimicrobial-mildew resistant nish with an exclusive BEHR MARQUEE Interior One-Coat Color Collection*.
RECOMMENDED USES:
This product is ideal for every room and delivers a radiant, sleek nish. Use on properly prepared, primed or previously
painted interior surfaces such as:
• Concrete • Concrete Block/CMU • Brick • Plaster
• Drywall/Gypsum Board • Wood • Ferrous Metals • Galvanized Steel
• Aluminum • Other Non-Ferrous Metal
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 3450 127 oz. / 3 oz.
No. 3454 116 oz. / 14 oz.
No. 3453 112 oz. / 18 oz.
Gloss: 45-55 @ 60°
Resin Type: 100% Acrylic Latex
Weight per Gallon: 10.88 lbs.
% Solids by Volume: 41.2%
% Solids by Weight: 54.4%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 90-110 KU
Recommended Film Thickness:
Wet: 4.0 Dry: 1.6 mils @ 400 Sq. Ft./Gal.
Coverage: Up to 400 Sq. Ft./Gal. depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8" - 1/2" nap
Airless Spray: At packaged consistency
Tip: .015"- .019"
Filter: 60 mesh
Thinning: (If required) No more than 1/2 pint of water
per gallon.
Dry Time: @ 77° & 50% RH
Longer dry time may be required in cooler temperatures
and higher humidity.
To Touch: 1 hour
To Recoat: 2 hours
Full Cure: 4 weeks
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling
paint, rust and all other foreign substances.
New Drywall: All drywall surfaces should be suciently
sanded smooth. Remove any remaining drywall dust prior to
priming. Allow all drywall compounds to be completely dry
prior to coating. Previously Painted Drywall:
Remove all loose and peeling paint and all other foreign
substances. Clean any dirt and grease by scrubbing the
surface with a detergent and water solution, followed by a
thorough rinsing with clean water. Set nails and ll holes,
scratches, and gouges with the appropriate spackling
material. Let dry completely and sand smooth. Remove all
dust with a wiping cloth. Fill all gaps with a 100% acrylic,
siliconized, paintable caulking, and allow to completely dry
prior to coating. Glossy Surfaces: For maximum adhesion,
sand the surface thoroughly before coating.
New Wood: Remove mill glaze with sandpaper.
Set nails and ll holes, scratches, and gouges with the
appropriate wood ller and let dry completely. Remove all
dust with a wiping cloth. Fill all gaps with a 100% acrylic,
siliconized, paintable caulking, and allow to completely dry
prior to coating.
Previously Painted Wood: Remove all loose and peeling
paint and all other foreign substances. Clean any dirt and
grease by scrubbing the surface with a detergent and
water solution, followed by a thorough rinsing with clean
water. Set nails and ll holes, scratches, and gouges with
the appropriate wood ller and let dry completely. Remove
all dust with a tack or wiping cloth. Fill all gaps with a
100% acrylic, siliconized, paintable caulking, and allow to
completely dry prior to coating. Glossy Surfaces:
For maximum adhesion, sand the surface thoroughly
before coating.
Wood: WARNING! Sanding or scraping pressure treated
lumber may be hazardous; wear appropriate protection.
Tannin Bleed & Stainblocking: After priming, test for
stain bleed-through by applying the topcoat to a small
section. If the stain bleeds through the topcoat, apply a
second coat of primer and test again before top-coating
the entire area. If bleeding continues, a longer dry time
of the primer may be needed before top- coating or an
additional coat of primer may be required to block the
tannin bleed or stain.
New Plaster: New plaster should be thoroughly dried
out and cured for a minimum of 30 days before painting.
When cured, clean using a mixed solution of one part
vinegar and one part water to remove eorescence and
neutralize. Previously Painted Plaster: Remove all
loose and peeling paint and all other foreign substances.
Clean any dirt and grease by scrubbing the surface with
a detergent and water solution, followed by a thorough
rinsing with clean water. Set nails and ll holes, scratches,
and gouges with the appropriate spackling material and
let dry completely and sand smooth. Remove all dust with
a tack or wiping cloth. Fill all gaps with a 100% acrylic,
siliconized, paintable caulking, and allow to completely dry
prior to coating. Glossy Surfaces: For maximum adhesion,
sand the surface thoroughly before coating.
Stain-Blocking: After priming, test for stain
bleed-through by applying the topcoat to a small section.
If the stain bleeds through the topcoat, apply a second
coat of primer and test again before top-coating the
entire area. If bleeding continues, a longer dry time
may be needed before top-coating.
Masonry: All masonry surfaces must be cured at least
30 days before painting. The pH must be 10.0 or lower prior
to coating. Smooth masonry may require an adequate
prole for adhesion. For all other smooth concrete, create a
prole using a product such as BEHR PREMIUM®
Concrete & Masonry Cleaner & Etcher No. 991 or with
mechanical means. Remove loose aggregate and debris
using a product such as BEHR PREMIUM
Concrete & Masonry Degreaser & Cleaner No. 990.
COMPLIES WITH THE BELOW AS OF 1/1/2017
SCAQMD YES LEED v.4
†
YES
CARB YES MPI# 54, 141
OTC YES MPI X - Green 54, 141
LADCO YES GREENGUARD YES
AIM YES CHPS YES
LEED v.3 (2009)
†
YES NAHB/ICC NGBS YES
This coating conforms to USDA regulatory requirements
for incidental food-contact materials intended for use
on surfaces not in direct contact with food, such as walls,
oors and ceilings.
†
Please visit www.usgbc.org/LEED for additional details.