TDS
TECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2014 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 11/2015
2 of 2
mechanical means. Remove loose aggregate and debris
using a product such as BEHR PREMIUM® Concrete &
Masonry Cleaner & Etcher No. 991.
Metals: Ferrous and Non-Ferrous Metals: All metals
should be clean and free of any oils, rust, mill scale or other
contaminants. All metals require sucient “tooth” or prole
for optimum adhesion and therefore require some type of
sanding, abrasion, or chemical etching. Oil lms:
(especially on new or non-ferrous metals) should be
removed by scrubbing the surface with a detergent and
water solution, and thoroughly rinsed. Rust and Mill
Scale: Remove all rust and mill scale using sandpaper,
steel wool, abrasive blasting, or other abrading methods.
Prole: For best adhesion results, sand all metal surfaces
(including new ones) with sandpaper, steel wool, or etch
using a product such as BEHR PREMIUM® Concrete &
Masonry Cleaner & Etcher No. 991. Clean by scrubbing the
surface with a detergent and water solution, followed by a
thorough rinsing with clean water. All ferrous metals must
be primed the same day it is cleaned to prevent rust.
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD or
visit www.epa.gov/lead.
RECOMMENDED PRIMER/SYSTEMS:
PROPERLY PREPARED NEW SURFACES:
Wood: Cedar, Redwood, Shakes & Shingles;
For Severe Tannin Bleed/Stainblocking:
• BEHR PREMIUM PLUS® Exterior Multi-Surface Primer
& Sealer No. 436
Tannin/Stainblocking:
• BEHR PREMIUM PLUS Exterior Multi-Surface Primer
& Sealer No. 436
Masonry: Stucco, Cinder Block, Cut Masonry Unit’s
(CMUs), Split Face Block
• BEHR PREMIUM Interior/Exterior Basement & Masonry
Waterproofer No. 875 or BEHR PREMIUM Interior/Exterior
Concrete & Masonry Waterproofer No. 870
Masonry: Cement Composition Panels/Siding,
Exterior Insulation and Finish Systems (EIFS)
or Synthetic Stucco
• BEHR PREMIUM Interior/Exterior Basement & Masonry
Waterproofer No. 875 or BEHR PREMIUM Interior/Exterior
Concrete & Masonry Waterproofer No. 870
Masonry with pH Levels up to 13.0:
• BEHR PREMIUM Interior/Exterior Basement & Masonry
Waterproofer No. 875 or BEHR PREMIUM Interior/Exterior
Concrete & Masonry Waterproofer No. 870
• BEHR PREMIUM PLUS Exterior Multi-Surface Primer
& Sealer No. 436
Ferrous and Non-Ferrous Metals:
• BEHR PREMIUM PLUS Exterior Multi-Surface Primer
& Sealer No. 436
PREVIOUSLY PAINTED SURFACES:
• Use a full coat, or spot prime repaired, or uncoated
surfaces, such as woods with heavy tannins (Redwood
and Cedar) with BEHR MARQUEE® paint. Two coats may be
required.
TEST SPECIFICATIONS:
Scrubbability:
ASTM D2486 Scrub > 2500 (no shim)
Biological Growth:
ASTM D3273 (4 weeks) – Pass
Accelerated Weathering:
ASTM D4587, 500 hrs exposure - Pass
CLEAN UP:
Clean all tools and equipment with clean water. For disposal
of empty containers and unused product, contact your
household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Do not use on oors.
• Do not use when air and surface temperatures are below
35°F and above 90°F.
• Avoid heavy trac for 24 hours.
• Allow four weeks before washing or cleaning for full cure.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Wear protective
clothing, gloves, and eye & face protection. Do not
eat, drink, or smoke when using this product. Take o
contaminated clothing and wash it before reuse.
Wash hands thoroughly after handling. Dispose of unused
contents, container and other contaminated wastes in
accordance with local, state, federal and
provincial regulations.
First aid: If in eyes: Rinse cautiously with water for several
minutes and remove contacts if present and easy to do.
Continue rinsing and get medical attention if eye irritation
persists. If on skin: Wash with plenty of soap and water.
If swallowed: Rinse mouth and get medical attention
if you feel unwell.
EXTERIOR FLAT PAINT
NO. 4450 ULTRA PURE WHITE®