TDS
TECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2016 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 6/2016
1 of 2
EXTERIOR SATIN ENAMEL PAINT
NO. 9450 ULTRA PURE WHITE®
PRODUCT INFORMATION
BEHR MARQUEE® Stain Blocking Paint & primer delivers remarkable dirt and fade resistance for exterior application.
Provides a tough, non-stick surface helping to prevent dirt adhesion, while UV protection technology delivers longer lasting
color. The paint lm is also able to resist rain as early as 60 minutes after application. Exterior nishes will look freshly
painted longer, even under the most challenging weather conditions.
RECOMMENDED USES:
Use on properly prepared, primed or previously painted exterior surfaces such as:
• Concrete • Cement Board Siding • Brick
• Stucco • Wood • Plywood
• Ferrous Metals • Non-Ferrous Metals
Note: Chalky substrates must be thoroughly cleaned to remove all chalk by pressure washing or other suitable methods.
All loose & peeling paint must be removed prior to painting or priming.
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 9450 128 oz. / 2 o.z
No. 9454 120 oz. / 10 oz.
No. 9453 116 oz. / 14 oz.
Gloss: 15-25 @ 60°
Sheen: >35 @ 85°
Resin Type: 100% Acrylic Latex
Weight per Gallon: 10.2 lbs.
% Solids by Volume: 38%
% Solids by Weight: 48.5%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 100-110 KU
Recommended Film Thickness:
Wet: 6.4 mils / Dry: 2.4 mils @ 250 Sq. Ft./Gal.
Wet: 4.0 mils / Dry: 1.5 mils @ 400 Sq. Ft./Gal.
Coverage: 250-400 Sq. Ft./Gal. depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller:
Smooth Surface: 3/8" - 1/2" nap
Rough Surface: 1/2" - 3/4" nap
Airless Spray: At packaged consistency
Tip: .015"- .021"
Filter: 60 mesh
Thinning: (If required) No more than 1/2 pint
of water per gallon.
Dry Time: @ 77° & 50% RH
To Touch: 1 hour
To Recoat: 2 hours (3 hours for deep base)
Full Cure: 4 weeks
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling
paint, rust, and all other foreign substances.
New Drywall: All drywall surfaces should be suciently
sanded smooth. Remove any remaining drywall dust prior
to priming. Allow all drywall compounds to be completely
dry prior to coating. Previously Painted Drywall: Remove
all loose and peeling paint and all other foreign substances.
Clean any dirt and grease by scrubbing the surface with
a detergent and water solution, followed by a thorough
rinsing with clean water. Set nails and ll holes, scratches,
and gouges with the appropriate spackling material and
let dry completely and sand smooth. Remove all dust with
a wiping cloth. Fill all gaps with a 100% acrylic, siliconized,
paintable caulking, and allow to completely dry prior to
coating. Glossy Surfaces: For maximum adhesion, sand the
surface thoroughly before coating.
New Wood: Remove mill glaze with sand paper. Set nails
and ll holes, scratches, and gouges with the appropriate
wood ller and let dry completely. Remove all dust with a
wiping cloth. Fill all gaps with a 100% acrylic, siliconized,
paintable caulking, and allow to completely dry prior to
coating. Previously Painted Wood: Remove all loose and
peeling paint and all other foreign substances. Clean any dirt
and grease by scrubbing the surface with a detergent and
water solution, followed by a thorough rinsing with clean
water. Set nails and ll holes, scratches, and gouges with the
appropriate wood ller and let dry completely. Remove all
dust with a tack or wiping cloth. Fill all gaps with a
100% acrylic, siliconized, paintable caulking, and allow
to completely dry prior to coating. Glossy Surfaces:
For maximum adhesion, sand the surface thoroughly
before coating.
Wood: WARNING! Sanding or scraping pressure treated
lumber may be hazardous; wear appropriate protection.
New Plaster: New plaster should be thoroughly dried
out and cured for a minimum of 30 days before painting.
When cured, clean using a mixed solution of one part
vinegar and one part water to remove eorescence and
neutralize. Previously Painted Plaster: Remove all
loose and peeling paint and all other foreign substances.
Clean any dirt and grease by scrubbing the surface with
a detergent and water solution, followed by a thorough
rinsing with clean water. Set nails and ll holes, scratches,
and gouges with the appropriate spackling material.
Let dry completely and sand smooth. Remove all dust with
a tack or wiping cloth. Fill all gaps with a 100% acrylic,
siliconized, paintable caulking, and allow to completely dry
prior to coating. Glossy Surfaces: For maximum adhesion,
sand the surface thoroughly before coating.
Stainblocking: After priming, test for stain bleed-through
by applying the topcoat to a small section. If the stain bleeds
through the topcoat, apply a second coat of primer and
test again before topcoating the entire area. If bleeding
continues, a longer dry time of the primer may be needed
before topcoating.
Masonry: All masonry surfaces must be cured at least
30 days before painting. The pH must be 10.0 or lower prior
to coating. Smooth masonry may require an adequate
prole for adhesion. For all other smooth trowel concrete,
create a prole using a product such as a muriatic acid etcher
or with mechanical means. Remove loose aggregate and
debris using a product such as a muriatic acid etcher.
COMPLIES WITH THE BELOW AS OF 6/1/2016
SCAQMD YES LEED v.4
†
YES
CARB YES MPI#
15, 315
OTC YES GREENGUARD YES
LADCO YES CHPS YES
AIM YES NAHB/ICC NGBS YES
LEED v.3 (2009)
†
YES
†
Please visit www.usgbc.org/LEED for additional details.