TDS
TECHNICAL DATA SHEETTECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative, call
1-800-854-0133 Ext. 2 (U.S.A. only). ©2020 Behr Process Corporation Santa Ana, CA 92705 U.S.A.
Revised 6/2020
ADVANCED DECKOVER® SMOOTH COATING
NO. 5000
1 of 2
PRODUCT INFORMATION
BEHR PREMIUM ADVANCED DECKOVER® Smooth is an innovative solid color coating that resurfaces properly prepared weathered
wood and concrete. The advanced 100% acrylic resin creates a durable coating on your tired deck, rejuvenating its look.
ADVANCED DECKOVER Smooth is designed to conceal splinters & cracks up to 1/4" and creates a smooth, slip-resistant nish.
Our latest formula now features even better adhesion and cracking resistance. It can be tinted to 54 solid custom colors.
RECOMMENDED USES:
Recommended for properly prepared interior and exterior weathered or cracked horizontal and vertical surfaces such as:
• Wood • Composite • Concrete
Do not use on drivable surfaces such as garage oors and driveways.
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 5000 Deep Base 116 oz / 14 oz
Resin Type: 100% Acrylic
Weight per Gallon: 11.45 lb
% Solids by Volume: 51% ± 2%
% Solids by Weight: 65% ± 2%
VOC: < 50 g/L
Flash Point: N/A
Viscosity: 95 – 105 KU (Paste Paddle)
Recommended Film Thickness:
Wet: 10.7 mils / Dry: 5.5 mils per coat
(Total Dry Film Thickness: 10.9 mils for 2 coats)
Coverage: 75 sq ft/gal in two coats (required)
APPLICATION:
Brush: Nylon/polyester
Roller: 1/4" – 1/2" nap roller cover, depending on surface
texture
Airless Spray: At packaged consistency
Tip: .027" – .035"
Filter: Remove
Fluid Pressure: 2,400 – 3,200 psi
• For nail holes and cracks up to 1/4", completely ll in with
ADVANCED DECKOVER Coating using a nylon/polyester
brush and allow to dry prior to rolling. Deep nailholes and
cracks require additional lling.
• Use pressure while rolling and apply a generous, even coat
using a 1/2" nap roller. For a smoother texture, use a brush
or thinner nap roller (i.e., 1/4")
• For optimum performance, lm uniformity, leveling,
adhesion and crack lling, a second coat MUST be applied.
• Maintain a wet edge when applying.
• For best results, coat all accessible board ends.
• Airless spray is recommended for experienced applicators
only. When spraying vertical surfaces, apply a very thin coat
(one pass only) at a spread rate of 400 sq ft/gal and do not
back brush/roll. When spraying horizontal surfaces, follow
the standard spread rate of 75 sq ft/gal.
Thinning: DO NOT THIN. Product is formulated for use at
package consistency only.
Dry Time: 77°F & 50% RH
To Touch: 4 hours
To Recoat: 4 – 6 hours
Light Foot Trac: 24 – 48 hours
Full Cure: 72 hours
Dry times are temperature, humidity, and lm thickness
dependent.
SURFACE PREPARATION:
The following steps and products are required:
All surfaces must be clean, sound, dry and free of any dirt,
oil, and grease before application.
Wood Surfaces: Replace rotting or unstable boards and
remove loose splinters. Remove mildew stains, dirt, oil and
grease with a product such as BEHR PREMIUM® No. 63
All-In-One Wood Cleaner prior to application. Use a
product such as BEHR PREMIUM No. 64 Wood Stain & Finish
Stripper (must be followed by No. 63) to remove all loose
wood bers, peeling paint/stain or deteriorated coatings
prior to application of DECKOVER®. On new wood, use No.
63 to remove mill glaze and open the pores of the wood.
Concrete Surfaces: Avoid areas that are structurally weak
or subject to hydrostatic pressure up to 8 psi. Allow new
surfaces to cure for 30 days. Clean and etch surface using a
product such as a muriatic acid to achieve a textured prole
similar to 150 grit sandpaper. Follow all label instructions.
If the previous coating is failing or peeling, use a paint
stripper to remove old coating.
After etching or using either No. 64 or No. 63, rinse
thoroughly with a garden hose or pressure washer.
When rinsing with a pressure washer, use the broadest spray
pattern while keeping the nozzle at least 24" away from
the surface. Allow the area to dry at least 24 hours before
coating. If needed, lightly sand to remove any wood
bers/fuzz.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSHapproved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEAN UP/DISPOSAL:
Clean all tools and equipment with warm, soapy water.
Do not dispose of this product down a drain. If spilled,
contain material and remove with an inert absorbent.
Dispose of contaminated absorbent, container and
unused product in accordance with all current federal,
state and local regulations. For recycling or disposal of
empty containers, unused product and soiled rags,
contact your household refuse collection service.
COMPLIES WITH THE BELOW AS OF 6/1/2020
SCAQMD YES LADCO YES
CARB SCM 2007 YES AIM YES
OTC Phase II YES MPI# 127
OTC YES