TDS

TECHNICAL DATA SHEETTECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative, call
1-800-854-0133 Ext. 2 (U.S.A. only). ©2020 Behr Process Corporation Santa Ana, CA 92705 U.S.A.
Revised 6/2020
ADVANCED DECKOVER® TEXTURED COATING
NO. 5005
1 of 2
PRODUCT INFORMATION
BEHR PREMIUM ADVANCED DECKOVER® Textured is an innovative, waterproong solid color coating that will bring your
old, weathered wood or concrete back to life. The advanced 100% acrylic resin creates a durable coating on your tired deck,
rejuvenating its look. ADVANCED DECKOVER Textured is designed to conceal splinters & cracks up to 1/4" and creates a textured,
slip-resistant nish. It can be tinted to 54 solid custom colors.
RECOMMENDED USES:
Recommended for properly prepared above grade interior and exterior weathered or cracked horizontal and vertical surfaces such as:
• Wood • Composite • Concrete
Do not use on drivable surfaces such as garage oors and driveways.
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 5005 Deep Base 116  oz / 14  oz
Resin Type: 100% Acrylic
Weight per Gallon: 11.5 lbs
% Solids by Volume: 51% ± 2%
% Solids by Weight: 64% ± 2%
VOC: < 50 g/L
Flash Point: N/A
Viscosity: 87 – 115 KU (Paste Paddle)
Recommended Film Thickness:
Wet: 10.6 mils / Dry: 5.4 mils
(Total Dry Film Thickness: 10.9 mils for 2 coats)
Coverage: 75 sq ft/gal for 2 coats (required)
APPLICATION:
Brush: Nylon/Polyester
Roller: 1/4" – 1/2" nap roller cover, depending on surface
texture
Spray: DO NOT USE WITH AIRLESS SPRAYER
• For nail holes and cracks up to 1/4", completely ll in with
ADVANCED DECKOVER Coating using a nylon/polyester
brush and allow to dry prior to rolling. Deep nail holes and
cracks require additional lling.
• Use pressure while rolling and apply generously.
• For optimum performance, lm uniformity, leveling,
adhesion and crack lling, a second coat MUST be applied.
Maintain a wet edge when applying.
• For best results, coat all accessible board ends.
• To create an Extra Textured nish, use Extra Textured
roller cover.
• For vertical surfaces such as railings, use a nylon/polyester
brush or roller and apply two thin coats at a spread rate of
400 sq ft/gal.
Thinning: DO NOT THIN. Product is formulated for use
at package consistency only.
Dry Time: 77°F & 50% RH
To Touch: 4 hours
To Recoat: 4 – 6 hours
Light Foot Trac: 24 – 48 hours
Full Cure: 72 hours
Dry times are temperature, humidity, and lm thickness
dependent.
SURFACE PREPARATION:
The following steps and products are required:
(Proper surface preparation is required.)
Exterior Wood Surfaces: Replace rotting or unstable
boards and remove loose splinters. For exterior failing
coatings or to remove loose wood bers, use a product such
as BEHR PREMIUM® No. 64 Wood Stain & Finish Stripper
followed by BEHR PREMIUM No. 63 All-In-One Wood Cleaner
to neutralize the wood. When No. 64 is not needed, a
product such as No. 63 MUST be used to remove mill glaze
and clean the exterior wood surface. After using either
No. 64 or No. 63, rinse thoroughly with a garden hose or
pressure washer. When rinsing with a pressure washer, use
the broadest spray pattern while keeping the nozzle at least
24" away from the surface. Allow the area to dry at least
24 hours before coating. Lightly sand to remove remaining
wood bers/fuzz.
Concrete Surfaces: Avoid areas that are structurally weak
or subject to hydrostatic pressure above 8 psi. Allow new
surfaces to cure for 30 days. Clean and etch surface using a
product such as a muriatic acid to achieve a textured prole
similar to 150 grit sandpaper. Follow all label instructions.
If the previous coating is failing or peeling, use a paint
stripper to remove old coating.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEAN-UP/DISPOSAL:
Clean all tools and equipment with warm, soapy water.
Do not dispose of this product down a drain. If spilled,
contain material and remove with an inert absorbent.
Dispose of contaminated absorbent, container and unused
product in accordance with all current federal, state
and local regulations. For recycling or disposal of empty
containers, unused product and soiled rags, contact your
household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• While this textured product provides a slip resistant nish,
surfaces may still become slippery when wet.
• Do not use on drivable surfaces such as garage oors and
driveways.
• For best results, apply when air, material and surface
temperatures are between 50°F and 90°F. Temperatures
above 90°F can cause the paint to dry too fast,
whereas temperatures below 50°F can inhibit proper
lm formation.
• Do not use if rain is expected within 24 hours and avoid
painting if humidity is expected to be greater than 80%.
• Avoid applying paint in direct sunlight or hot surfaces.
• Test product for color on a small hidden area before
proceeding.
COMPLIES WITH THE BELOW AS OF 6/1/2020
SCAQMD YES LADCO YES
CARB SCM 2007 YES AIM YES
OTC Phase II YES MPI
#
127
OTC YES FLAME SPREAD/CLASS A YES