TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2018 Behr Process Corporation Santa Ana, CA 92705 U.S.A.
Revised 12/2018
1 of 1
ADVANCED DECKOVER® TEXTURED COATING
NO. 5005
PRODUCT INFORMATION
BEHR PREMIUM ADVANCED DECKOVER® Textured is an innovative , waterproong solid color coating that will bring your
old, weathered wood or concrete back to life. The advanced 100% acrylic resin creates a durable coating on your tired deck,
rejuvenating its look. ADVANCED DECKOVER Textured is designed to conceal splinters & cracks up to 1/4" and creates a textured,
slip-resistant nish. It can be tinted to 54 solid custom colors.
RECOMMENDED USES:
Recommended for properly prepared interior and exterior weathered or cracked horizontal and vertical surfaces such as:
• Wood • Composite • Concrete
Do not use on drivable surfaces such as garage oors and driveways.
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 5005 Deep Base 116  oz / 14  oz
Resin Type: 100% Acrylic
Weight per Gallon: 11.5 lbs
% Solids by Volume: 51% +/- 2%
% Solids by Weight: 65% +/- 2%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 95-105 KU (Paste Paddle)
Recommended Film Thickness:
Wet: 10.6 mils Dry: 5.4 mils per coat
(Total Dry Film Thickness: 10.9 mils for 2 coats)
Coverage: 75 sq ft/gal for 2 coats (required)
APPLICATION:
Brush: Nylon/polyester brush
Roller: 1/4"- 1/2" nap
DO NOT USE WITH AIRLESS SPRAYER
Dry Time: @ 77°F & 50% RH
To Recoat: 4-6 hours
Light Foot Trac: 24-48 hours
Full Cure: 72 hours
• For nail holes and cracks up to 1/4”, completely ll in with
ADVANCED DECKOVER Coating using a nylon/polyester
brush and allow to dry prior to rolling. Deep nail holes and
cracks require additional lling.
• Use pressure while rolling and apply generously.
• For optimum performance, lm uniformity, leveling,
adhesion and crack lling, a second coat MUST be applied.
Maintain a wet edge when applying.
• For best results, coat all accessible board ends.
• To create an Extra Textured nish, use Extra Textured roller cover.
SURFACE PREPARATION:
The following steps and products are required:
(Proper surface preparation is required.) Exterior Wood
Surfaces: Replace rotting or unstable boards and remove
loose splinters. For exterior failing coatings or to remove
loose wood bers, use a product such as BEHR PREMIUM®
No. 64 Wood Stain & Finish Stripper followed by
BEHR PREMIUM No. 63 All-In-One Wood Cleaner to
neutralize the wood. When No. 64 is not needed, a product
such as No. 63 MUST be used to remove mill glaze and
clean the exterior wood surface. After using either No. 64
or No. 63, rinse thoroughly with a garden hose or pressure
washer. When rinsing with a pressure washer, use the
broadest spray pattern while keeping the nozzle at least
24" away from the surface. Allow the area to dry at least
24 hours before coating. Lightly sand to remove
remaining wood bers/fuzz.
Concrete Surfaces: Avoid areas that are structurally
weak or subject to hydrostatic pressure above 8 psi.
Allow new surfaces to cure for 30 days. Clean and etch
surface using a product such as a muriatic acid to
achieve a textured prole similar to 150 grit sandpaper.
Follow all label instructions. If the previous coating is failing
or peeling, use a paint stripper to remove old coating.
See behr.com for additional product information.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or log on
to www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with clean water. For proper
disposal of empty containers and unused product, contact
your household refuse collection service.
CAUTIONS/LIMITATIONS:
• While this textured product provides a slip resistant nish,
surfaces may still become slippery when wet.
• Use product when air and surface temperatures are
between 50-90° F.
• Do not use if rain is expected within 24 hours and avoid
painting if humidity is expected to be greater than 80%.
• Avoid applying paint in direct sunlight or hot surfaces.
• Do not use on drivable surfaces such as garage oors and
driveways.
• Do not use without the addition of tinting colorants.
• DO NOT THIN PRODUCT.
• Test product for color on a small hidden area before
proceeding.
• Protect from freezing.
• Shelf life under normal conditions is two years (unopened
containers).
GENERAL INFORMATION:
CAUTION IRRITANT HARMFUL IF SWALLOWED.
MAY CAUSE EYE, NOSE AND THROAT IRRITATION.
AVOID CONTACT WITH SKIN AND EYES AND AVOID
BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE
PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH
ADEQUATE VENTILATION.To avoid breathing vapors and
spray mist, open windows and doors or use other means to
ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase
fresh air. If properly used, a respirator
(NIOSH approved for organic vapor with P series
particulate pre-lter) may oer additional protection.
A dust mask does not provide protection against vapors.
Avoid contact with eyes and skin. Wash thoroughly after
handling. Close container after each use. FIRST AID:
If you experience diculty in breathing, leave the area to
obtain fresh air. If continued diculty is experienced, get
medical assistance immediately. In case of eye contact,
ush immediately with plenty of water for at least
20 minutes and get medical attention; for skin,
wash thoroughly with soap and water. If swallowed, get
medical attention immediately.
COMPLIES WITH THE BELOW AS OF 12/1/2018
SCAQMD YES LADCO YES
CARB SCM 2007 YES AIM YES
CARB YES LEED v.3 (2009)
†
YES
OTC Phase II YES MPI# 127
OTC YES FLAME SPREAD/CLASS A YES
†
Please visit www.usgbc.org/LEED for additional details.