Use and Care Manual

• Resurfaces Properly Prepared
Weathered Wood and Concrete
• Covers up to 75 Sq. Ft. in 2 Coats
• Textured or Extra Textured Finish
• Conceals Splinters & Cracks
up to 1/4"
• Resists Cracking & Peeling
• Durable, Mildew Resistant Finish
• Slip Resistant, Waterproof Coating
• 100% Acrylic
BEHR PREMIUM Advanced DeckOver
®
- Textured
LIMITED WARRANTY
For one year from the date of purchase, Behr Process Corporation warrants to the original consumer purchaser, (1) that the product
meets Behr Process Corporation’s manufacturing specifications, and (2) the performance of this product when applied according to the
label instructions and specifications. In the event this product proves to be defective within one year from the date of purchase, Behr
Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent
amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of
labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of
express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable
law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited
to the duration of this express warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state
to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply
to the fullest extent permitted by the laws of the State of New Jersey. To obtain warranty service, call 1-800-854-0133. Behr Process
Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
WHERE TO USE
Recommended for properly prepared interior and exterior weathered or
cracked horizontal and vertical wood and composite surfaces such as Decks,
Railings, Porches and Boat Docks. Can also be used on concrete surfaces
such as Pool Decks, Patios and Sidewalks. Do not use on drivable surfaces
such as garage floors and driveways. DO NOT USE ON wood surfaces
that are in direct contact with the ground or exposed to excessive ground
moisture.
SURFACE PREPARATION (Proper Surface Preparation is Required)
All surfaces must be clean, sound, dry and free of any dirt, oil, and grease
before application. Wood Surfaces: Replace rotting or unstable boards
and remove loose splinters. Remove mildew stains, dirt, oil and grease
with a product such as BEHR PREMIUM
®
No. 63 All-In-One Wood Cleaner
prior to application. Use a product such as BEHR PREMIUM No. 64 Wood
Stain & Finish Stripper (must be followed by No. 63) to remove all loose
wood fibers, peeling paint/stain or deteriorated coatings prior to application
of DECKOVER
®
. On new wood, use No. 63 to remove mill glaze and open
the pores of the wood. Rinse thoroughly and allow to dry before coating.
Concrete Surfaces: Avoid areas that are structurally weak or subject to
hydrostatic pressure above 8 psi. Allow new surfaces to cure for 30 days.
Use a product such as BEHR PREMIUM No. 992 Concrete & Masonry Paint
Stripper to strip peeling coating. Use a product such as BEHR PREMIUM No.
991 Concrete & Masonry Cleaner & Etcher to clean.
APPLICATION
Use product when air and surface temperatures are between 50-90˚ F.
• Avoid applying in direct sunlight or to hot surfaces.
• Do not use if rain is expected within 24 hours.
• The surface must be completely dry before application.
• Avoid painting if humidity is expected to be greater than 80%.
• Intermix multiple containers to ensure color uniformity.
• Stir product occasionally throughout application. DO NOT THIN PRODUCT.
• For nail holes and cracks up to 1/4", completely fill in with Textured
DECKOVER
®
coating using a nylon/polyester brush and allow to dry prior
to rolling.
• Deep nail holes and cracks may require additional filling.
• For edges, corners and in between wood boards, apply using a
nylon/polyester brush.
• Use pressure while rolling and apply a generous, even coat using a 1/2" nap
roller. For a smoother texture, use a brush or thinner nap roller (i.e. 1/4").
• For Extra Textured finish, use Extra Textured roller cover (spread rate
will decrease).
• For vertical surfaces such as railings, use a nylon/polyester brush or roller
and apply two thin coats at a spread rate of 400 sq. ft. per gallon.
• Do not use with airless sprayer.
• For optimum performance, film uniformity, leveling, to cover cracks and
proper adhesion,a second coat MUST be applied. Maintain a wet edge
when applying.
• For best results, coat all accessible board ends.
DRY TIME
4-6 hours before recoat. Dries to touch in 4 hours. Wait 24-48 hours before
light foot traffic. 72 hours to full cure. Additional dry time may be needed in
cooler temperatures and higher humidity. Premature heavy traffic will cause
coating failure.
DISPOSAL
For disposal of empty containers and unused product contact your household
refuse collection service.
WARNING! If you scrape, sand or remove old paint, you may release lead
dust. LEAD IS TOXIC. Contact the National Lead Information Center at
1-800-424-LEAD or log on to www.epa.gov/lead.
WARNING! Sanding or scraping pressure treated lumber may be hazardous;
wear appropriate protection.
WARNING! IRRITANT! HARMFUL IF SWALLOWED. CONTAINS: ACRYLIC RESIN.
MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES
AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE PROTECTION AND
PROTECTIVE CLOTHING. USE ONLY WITH ADEQUATE VENTILATION. To avoid breathing vapors
and spray mist, open windows and doors or use other means to ensure fresh air entry during application
and drying. If you experience eye watering, headaches or dizziness, increase fresh air. If properly used,
a respirator (NIOSH approved for organic vapor with P series particulate pre-filter) may offer additional
protection; obtain professional advice before using. A dust mask does not provide protection against vapors.
Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use. FIRST
AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is
experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of
water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water. If
swallowed, get medical attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.
To consult with a Behr Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).
©2018 Behr Process Corporation
Santa Ana, CA 92704 U.S.A. • behr.com
V.O.C. <50 g/L • REV. 12/18
Prep: Mandatory
Before Use
Clean-Up:
Soap & Water
Covers up to
75 Sq. Ft.
in 2 Coats
Conceal: Pre-fill Cracks
Less than 1/4” With
DECKOVER
2 Coats Required
1 2
No. 5005 Deep Base
Cancer and Reproductive Harm
www.P65warnings.ca.gov
WARNING