TDS
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2016 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 6/2016
2 of 2
Tannin Bleed & Stainblocking: After priming, test for
stain bleed-through by applying the top coat to a small
section. If the stain bleeds through the top coat, apply a
second coat of primer and test again before top coating
the entire area. If bleeding continues, a longer dry time
of the primer may be needed before topcoating or an
additional coat of primer may be required to block the
tannin bleed or stain.
Masonry: Stucco, Concrete, Cut Masonry Units (CMUs),
Split-Face Block: New: All masonry surfaces must be
cured at least 30 days before painting. The pH must be
10.0 or lower prior to coating. Smooth masonry may
require an adequate prole for adhesion. For all other
smooth concrete, create a prole using a product such
as a muriatic acid etcher or with mechanical means. Remove
loose aggregate and debris.
Masonry: Cement Composition Panels/Siding,
Exterior Insulation and Finish Systems (EIFS) or
Synthetic Stucco: New: All masonry surfaces must be
cured at least 30 days before painting. The pH must be
10.0 or lower prior to coating. All surfaces must be clean,
free of dust, chalk, mold and mildew stains, loose and
peeling paint and all other foreign substances. Clean surfaces
with a detergent and water solution by scrubbing the surface
vigorously and rinse with a garden hose or a power washer at
a low setting (500-1200 PSI). DO NOT USE HIGH PRESSURE as
this may harm the substrate.
Previously Painted Surfaces: All surfaces must be clean,
free of dust, chalk, mold and mildew stains, loose and
peeling paint and all other foreign substances. Clean surfaces
with a detergent and water solution by scrubbing the surface
vigorously and rinse with a garden hose or a power washer
and allow to dry.
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD
or visit www.epa.gov/lead.
RECOMMENDED PRIMER/SYSTEMS:
PROPERLY PREPARED NEW SURFACES:
Wood: Cedar, Redwood, Shakes & Shingles; For Severe
Tannin Bleed/Stainblocking:
• BEHR PREMIUM PLUS® Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Masonry with pH Levels up to 13.0:
• BEHR PREMIUM Interior/Exterior Basement &
Masonry Waterproofer No. 875
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Non-Ferrous Metal:
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
PREVIOUSLY PAINTED SURFACES:
• Use a full coat or spot prime repaired or uncoated surfaces
with such as woods with heavy tannins (Redwood and
Cedar) with BEHR PREMIUM PLUS ULTRA® Paint and Primer
in One. Two coats may be required.
TEST SPECIFICATIONS:
Scrubbability
ASTM D2486 Scrub > 2500 (no shim)
Biological Growth
ASTM D3273 (4 weeks) – Pass
Accelerated Weathering
ASTM D4587, 500 hrs exposure - Pass
CLEAN UP:
Clean all tools and equipment with clean water.
For disposal of empty containers and unused product,
contact your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Do not use on oors.
• For best results, apply at temperatures between 35°F -
90°F. Temperatures above 90°F may aect the dry time.
• Avoid heavy trac for 24 hours.
• Allow four weeks before washing or cleaning for full cure.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Harmful if
swallowed. Wear protective clothing, gloves, eye, and
face protection. Do not eat, drink, or smoke when using
this product. Collect spillage and avoid release to the
environment. Take o contaminated clothing and wash it
before reuse. Wash hands thoroughly after handling.
Dispose of unused contents, container and other
contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for several
minutes and remove contacts if present and easy to do.
Continue rinsing and get medical attention if eye irritation
persists. If swallowed: Rinse mouth and get medical
attention if you feel unwell. If on skin: Wash with
plenty of soap and water.
EXTERIOR FLAT PAINT
NO. 4850 ULTRA PURE WHITE®