TDS
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2017 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
*
For as long as you reside in your home. See product label for details.
1 of 1
INTERIOR DRYWALL PRIMER & SEALER
NO. 73
PRODUCT INFORMATION
BEHR PREMIUM PLUS® Interior Drywall Primer & Sealer is fast-drying and seals uncoated and previously painted interior drywall,
wallboard, and wood to promote a uniform nish for topcoats. This 100% Acrylic formula provides outstanding adhesion and hiding
properties for topcoat products.
RECOMMENDED USES:
Use for interior applications in low moisture areas on new or unpainted:
• Drywall/Gypsum Board • Wallboard
• Plaster • Wood
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 73 126 oz. / 4 oz.
Resin Type: 100% Acrylic Latex
Weight per Gallon: 10.1 lbs.
% Solids by Volume: 23%
% Solids by Weight: 36.3%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 100 KU
Recommended Film Thickness:
Wet: 6.4 mils/Dry: 1.4 @ 250 Sq. Ft./Gal.
Wet: 4.0 mils/Dry: 0.9 mils @ 400 Sq. Ft./Gal.
Coverage: 250-400 Sq. Ft./Gal. depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8" - 1/2" nap
Airless Spray: At package consistency
Tip: .015"- .019"
Filter: Remove
Thinning: Not recommended. Product is formulated for use
at package consistency only.
Dry Time: @ 77° & 50% RH
Longer dry time may be required in cooler temperatures
and higher humidity.
To Touch: 30 minutes
To Recoat: 1 hour
Full Cure: 2 Weeks
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling paint,
rust, and all other foreign substances.
New Drywall: All drywall surfaces should be suciently
sanded smooth. Remove any remaining drywall dust prior to
priming. Allow all drywall compounds to be completely dry
prior to coating. Glossy Surfaces: For maximum adhesion,
sand the surface thoroughly before coating.
New Plaster: New plaster should be thoroughly dry
and cured for a minimum of 30 days before painting.
When cured, clean using a mixed solution of one part vinegar
and one part water to remove eorescence and neutralize.
Previously Painted Plaster: Remove all loose and peeling
paint and all other foreign substances. Clean any dirt and
grease by scrubbing the surface with a detergent and water
solution, followed by a thorough rinsing with clean water.
Set nails and ll holes, scratches, and gouges with the
appropriate spackling material. Let dry completely and
sand smooth. Remove all dust with a tack or wiping cloth.
Fill all gaps with a 100% acrylic, siliconized, paintable
caulking, and allow to completely dry prior to coating.
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD or
visit www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with clean water.
For disposal of empty containers and unused product,
contact your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Do not use on oors.
• For best results, apply at temperatures between
50°F - 90°F. Temperatures above 90°F may aect the
application such as drying too fast. Avoid painting
in direct sun.
NOTE: If the surface is hot to the touch it should be
considered too hot to apply this coating.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Wear protective
clothing, gloves, eye, and face protection. Do not eat, drink,
or smoke when using this product. Take o contaminated
clothing and wash it before reuse. Wash hands thoroughly
after handling. Dispose of unused contents, container and
other contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for several
minutes and remove contacts if present and easy to do.
Continue rinsing and get medical attention if eye irritation
persists. If on skin: Wash with plenty of soap and water.
If swallowed: Rinse mouth and get medical attention
if you feel unwell.
COMPLIES WITH THE BELOW AS OF 4/1/2017
SCAQMD YES LEED v.3 (2009)
†
YES
CARB SCM 2007 YES LEED v.4
†
YES
CARB YES MPI# 50
OTC Phase II YES MPI X-Green 50
OTC YES GREENGUARD® YES
LADCO YES CHPS YES
AIM YES NAHB/ICC NGBS YES
This coating conforms to USDA regulatory requirements for incidental food-
contact materials intended for use on surfaces not in direct contact with food,
such as walls, oors and ceilings.
†
Please visit www.usgbc.org/LEED for additional details.
GREENGUARD is a registered trademark of UL Company.
Revised 4/17