Use and Care Manual

CAUTION IRRITANT MAY CAUSE EYE, NOSE AND THROAT IRRITATION.
AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF
VAPORS AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE
CLOTHING. USE ONLY WITH ADEQUATE VENTILATION.To avoid breathing
vapors and spray mist, open windows and doors or use other means to ensure fresh air
entry during application and drying. If you experience eye watering, headaches or dizziness,
increase fresh air. If properly used, a respirator (NIOSH approved for organic vapor with P
series particulate pre-filter) may offer additional protection; obtain professional advice
before using. A dust mask does not provide protection against vapors. Avoid contact
with eyes and skin. Wash thoroughly after handling. Close container after each use.
FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If
continued difficulty is experienced, get medical assistance immediately. In case of eye contact,
flush immediately with plenty of water for at least 20 minutes and get medical attention; for
skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY.
*LIFETIME LIMITED WARRANTY Behr Process Corporation warrants to you, the original
residential consumer purchaser, the performance of this product as described on this label for
so long as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS
NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE
WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not to
perform as specified on the label during the warranty period, Behr Process Corporation will, at
its option and upon presentation of proof-of-purchase (the original receipt), either furnish an
equivalent amount of new product or refund the original purchase price of this product to you.
This warranty excludes (1) labor and costs of labor for the application or removal of any
product, and (2) any incidental or consequential damages, whether based on breach
of express or implied warranty, negligence, strict liability or any other legal theory.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you. This warranty gives you specific legal
rights and you may also have other rights, which vary from state to state. Note to residents
of the State of New Jersey: The provisions of this warranty, including its limitations, are
intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain
warranty service, call 1-800-854-0133. Behr Process Corporation reserves the right to inspect
any and all application of the product prior to processing your claim made under this warranty.
BEHR PREMIUM PLUS
®
Interior
All-In-One Primer & Sealer
• Blocks Medium to Heavy Stains
• Sticks to Glossy Surfaces
• Recommended for Use
Under High Sheen Paints
• High-Hide White
• Quick Recoat Time
• Mildew Resistant Finish
• 100% Styrene Acrylic
• Tintable up to 4 oz.
of Colorant per Gallon
• Low Odor
WHERE TO USE
Over properly prepared uncoated and previously painted interior
surfaces. Ideal for Drywall, Galvanized Metal, Vinyl, Aluminum, Wood,
Concrete, and on glossy surfaces or oil-based paint.
PREPARATION
All surfaces should be properly prepared and cleaned. Remove loose
paint, wash off chalk, dirt, and grease with detergent, rinse and allow
to dry. Remove mildew stains with a mildew stain removing product.
Scuff sand glossy surfaces and repair imperfections. Remove all dust
with a damp cloth, allow to dry. Allow new stucco, plaster and masonry
to cure for 30 days before priming.
APPLICATION
Apply when air and surface temperatures are between 50-90° F
(10-32° C). Use a high quality 3/8-1/2" nap roller cover, nylon polyester
brush or an airless sprayer (.015-.019" spray tip, 60 mesh filter). Stir
occasionally. Do not thin if using a roller or brush; however, if using a
sprayer and thinning is required, thin with water at a rate of no more
than 1/2 pint per gallon. Heavy stains may require two coats.
Spot prime patched areas first, follow with a complete primer coat.
Bright or deep colors require a tinted primer. Have primer tinted close
to topcoat color with no more than 4 ounces of colorant per gallon.
† On stained surfaces, topcoat in 4 hours, for heavy stains, topcoat in 16 hours.
DISPOSAL
For disposal of empty containers, unused paint and soiled rags, contact
your household refuse collection service.
Visit behr.com for painting tips, expert project advice and the perfect
color coordination with the ColorSmart by BEHR
®
Tool.
WARNING! If you scrape, sand or remove old paint, you may release lead
dust. LEAD IS TOXIC. Contact the National Lead Information Center at
1-800-424-LEAD or log on to www.epa.gov/lead.
To consult with a Behr Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).
No. 75 White
©2018 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. (C.O.V.) <5 g/L • REV. 10/18
30 Min Dries to Touch
1 Hr Ready to Topcoat
†
250-400 Sq. Ft.
Coverage per Gallon
Protect
from Freezing
Soap & Water
Clean-Up
• Zero VOC
- This product, like most Zero VOC paints, emits very low
amounts of VOCs.
- Most emissions occur during painting and for 48 hours after.
Some continue for two weeks or longer.
- While VOC emissions are very low, sensitive groups such as
babies and asthma/allergy sufferers should minimize exposure.
WARNING Cancer and Reproductive Harm – www.P65Warnings.ca.gov