TDS

ManualsBrandsBEHR Premium Plus ManualsPaint1-gal. Stain-Blocking Primer and Sealer Interior

TECHNICAL DATA SHEET

This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other

nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,

Revised 11/2015

1 of 2

INTERIOR ALLINONE PRIMER & SEALER

NO. 75

PRODUCT INFORMATION

BEHR PREMIUM PLUS® Interior All-In-one Primer & Sealer promotes excellent adhesion to dicult surfaces and provides

maximum stain resistance by locking in stains. It creates a uniform surface nish for improved hiding, adhesion and ow

and leveling of topcoats. This styrene acrylic latex lm is mildew resistant, adheres to glossy surfaces and locks in stains in

a multi-purpose stain-blocking formula.

RECOMMENDED USES:

This product is ideal over oil or water-based coatings, heavy stains and glossy surfaces. Use on all new and previously painted

or enameled interior surfaces such as:

• Concrete • Concrete Block/CMU • Brick

• Plaster • Drywall/Gypsum Board • Wood

• Wood Paneling • Non-Ferrous Metals • Architectural Plastics

PRODUCT SPECIFICATIONS:

Tint Bases/Max Tint Load:

No. 75 126 oz. / 6 oz.

Resin Type: Acrylic

Weight per Gallon: 11.2 lbs.

% Solids by Volume: 41.2%

% Solids by Weight: 56.6%

VOC: <5 g/L

Flash Point: N/A

Viscosity: 102-112 KU

Recommended Film Thickness:

Wet: 6.4 mils / Dry: 2.5 mils @ 250 Sq. Ft./Gal.

Wet: 4.0 mils / Dry: 1.6 mils @ 400 Sq. Ft./Gal.

Coverage: 250-400 Sq. Ft./Gal. depending on application

method and substrate porosity. Does not include the loss of

material from spraying.

APPLICATION:

Brush: Nylon/polyester

Roller: 3/8" - 1/2" nap

Airless Spray: At packaged consistency

Tip: .015"- .019"

Filter: Remove

Thinning: Not recommended. Product is formulated for use

at package consistency only.

Dry Time: @ 77° & 50% RH

Longer dry time may be required in cooler temperatures

and higher humidity.

To Touch: 30 minutes - 1 hour

To Recoat: 1 hour

Full Cure: 2 weeks

SURFACE PREPARATION:

All surfaces must be clean, free of dust, chalk, oil, grease,

wax, polish, mold and mildew stains, loose and peeling

paint, rust, and all other foreign substances.

New Drywall: All drywall surfaces should be suciently

sanded smooth. Remove any remaining drywall dust prior

to priming. Allow all drywall compounds to be completely

dry prior to coating. Previously Painted Drywall: Remove

all loose and peeling paint and all other foreign substances.

Clean any dirt and grease by scrubbing the surface with

a detergent and water solution, followed by a thorough

rinsing with clean water. Set nails and ll holes, scratches,

and gouges with the appropriate spackling material. Let dry

completely and sand smooth. Remove all dust with a wiping

cloth. Fill all gaps with a 100% acrylic, siliconized, paintable

caulking, and allow to completely dry prior to coating.

Glossy Surfaces: For maximum adhesion, sand

the surface thoroughly before coating.

New Wood: Remove mill glaze with sandpaper.

Set nails and ll holes, scratches, and gouges with

the appropriate wood ller and let dry completely.

Remove all dust with a wiping cloth. Fill all gaps with a

100% acrylic, siliconized, paintable caulking, and allow

to dry completely. Patched and lled surfaces should be

sanded smooth and dusted clean prior to coating.

Previously Painted Wood: Remove all loose and peeling

paint and all other foreign substances. Clean any dirt and

grease by scrubbing the surface with a detergent and water

solution, followed by a thorough rinsing with clean water.

Set nails and ll holes, scratches, and gouges with the

appropriate wood ller and let dry completely.

Remove all dust with a tack or wiping cloth. Fill all gaps

with a 100% acrylic, siliconized, paintable caulking, and

allow to completely dry prior to coating. Glossy Surfaces:

For maximum adhesion, sand the surface thoroughly to

provide a rough surface before coating.

Wood: WARNING! Sanding or scraping pressure treated

lumber may be hazardous; wear appropriate protection.

New Plaster: New plaster should be thoroughly dried

out and cured for a minimum of 30 days before painting.

When cured, clean using a mixed solution of one part

vinegar and one part water to remove eorescence and

neutralize. Previously Painted Plaster: Remove all loose

and peeling paint and all other foreign substances.

Clean any dirt and grease by scrubbing the surface with

a detergent and water solution, followed by a thorough

rinsing with clean water. Set nails and ll holes, scratches,

and gouges with the appropriate spackling material. Let dry

completely and sand smooth. Remove all dust with a tack

or wiping cloth. Fill all gaps with a 100% acrylic, siliconized,

paintable caulking, and allow to completely dry prior to

coating. Glossy Surfaces: For maximum adhesion, sand the

surface thoroughly before coating.

Stainblocking: After priming, test for stain bleed-through

by applying the topcoat to a small section. If the stain bleeds

through the topcoat, apply a second coat of primer and

test again before top-coating the entire area. If bleeding

continues, a longer dry time of the primer may be needed

before top-coating.

Masonry: All masonry surfaces must be cured at least

30 days before painting. The pH must be 10.0 or lower

prior to coating. Smooth masonry may require an

adequate prole for adhesion. For all other smooth trowel

concrete, create a prole using a product such as a muriatic

acid etcher or with mechanical means. Remove all loose

aggregate and debris.

Ferrous and Non-Ferrous Metal: The oil lm on new

non-ferrous metal must be removed before it is painted.

Remove oil lm with a detergent and water solution.

For better paint adhesion, sand the surface with sandpaper,

steel wool, or by using a product muriatic acid. Clean by

scrubbing the surface with a detergent and water solution,

COMPLIES WITH THE BELOW AS OF 9/1/2015

SCAQMD YES LEED v.4

†

YES

CARB YES MPI# 39, 50, 137

OTC YES MPI X - Green 50, 137

LADCO YES GREENGUARD® YES

AIM YES NAHB/ICC NGBS YES

LEED v.3 (2009)

†

YES

†

Please visit www.usgbc.org/LEED for additional details.

GREENGUARD is a registered trademark of UL Company.

Summary of content (2 pages)

PAGE 1
TECHNIC AL DATA SHEET INTERIOR ALL-IN-ONE PRIMER & SEALER N O. 75 PRODUCT INFORMATION BEHR PREMIUM PLUS® Interior All-In-one Primer & Sealer promotes excellent adhesion to difficult surfaces and provides maximum stain resistance by locking in stains. It creates a uniform surface finish for improved hiding, adhesion and flow and leveling of topcoats. This styrene acrylic latex film is mildew resistant, adheres to glossy surfaces and locks in stains in a multi-purpose stain-blocking formula.
PAGE 2
TECHNIC AL DATA SHEET INTERIOR ALL-IN-ONE PRIMER & SEALER N O. 75 followed by a thorough rinsing with clean water. Metal: Remove all rust and mill scale using sandpaper, steel wool, abrasive blasting, or other abrading methods to create a profile on the metal’s surface. New Surfaces: Clean the metal by scrubbing the surface with a detergent and water solution, followed by a thorough rinsing with clean water. Bare metal must be primed the same day it is cleaned.