TDS
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2016 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
*For as long as you reside in your home. See label for details.
Revised 12/2016
1 of 2
INTERIOR FLAT PAINT
NO. 1050 ULTRA PURE WHITE®
PRODUCT INFORMATION
BEHR PREMIUM PLUS® Interior Flat Paint is a GREENGUARD® Gold certified 100% acrylic paint & primer in one that contains
an antimicrobial agent to help protect the surface of the paint film from mold and mildew. This easy-clean flat provides
excellent touch-up, exceptional durability, hide and a non-reflective matte appearance. Formula is also low odor.
RECOMMENDED USES:
For low trac areas. Ideal for Family Rooms, Living Rooms, Dining Rooms, Bedrooms and Ceilings.
• Concrete • Concrete Block/CMU • Brick • Plaster
• Drywall/Gypsum Board • Wood • Ferrous Metals • Galvanized Steel
• Aluminum • Other Non-Ferrous Metal • Architectural Plastics
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 1050 128 oz. / 2 oz.
No. 1400 120 oz. / 10 oz.
No. 1300 116 oz. / 14 oz.
Pre-mixed colors:
No. 1012 Swiss Coee
No. 1052 White
Gloss: 0-4 @ 60°
Sheen: 0-4 @ 85°
Resin Type: 100% Acrylic Latex
Weight per Gallon: 12 lbs.
% Solids by Volume: 42.5%
% Solids by Weight: 60%
VOC: <5 g/L
Flash Point: N/A
Viscosity: 100-110 KU
Recommended Film Thickness:
Wet: 6.4 mils / Dry: 2.6 mils @ 250 Sq. Ft./Gal.
Wet: 4.0 mils / Dry: 1.6 mils @ 400 Sq. Ft./Gal.
Coverage: 250-400 Sq. Ft./Gal. depending on application
method and substrate porosity. Does not include the loss
of material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller:
Smooth Surface: 3/8" - 1/2" nap
Rough Surface: 1/2" - 3/4" nap
Airless Spray: At packaged consistency
Tip: .015"- .019"
Filter: 60 mesh
Thinning: (If required) No more than 1/2 pint
of water per gallon.
Dry Time: @ 77° & 50% RH
Longer dry time may be required in cooler temperatures
and higher humidity.
To Touch: 1 hour
To Recoat: 2 hours
Full Cure: 4 weeks
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling
paint, rust and all other foreign substances.
New Drywall: All drywall surfaces should be suciently
sanded smooth. Remove any remaining drywall dust prior
to priming. Allow all drywall compounds to be completely
dry prior to coating. Previously Painted Drywall: Remove
all loose and peeling paint and all other foreign substances.
Clean any dirt and grease by scrubbing the surface with
a detergent and water solution, followed by a thorough
rinsing with clean water. Set nails and ll holes, scratches,
and gouges with the appropriate spackling material. Let dry
completely and sand smooth. Remove all dust with a wiping
cloth. Fill all gaps with a 100% acrylic, siliconized, paintable
caulking, and allow to completely dry prior to coating.
Glossy Surfaces: For maximum adhesion, sand the
surface thoroughly before coating.
New Wood: Remove mill glaze with sandpaper. Set nails and
ll holes, scratches, and gouges with the appropriate wood
ller and let dry completely. Remove all dust with a wiping
cloth. Fill all gaps with a 100% acrylic, siliconized, paintable
caulking, and allow to completely dry prior to coating.
Previously Painted Wood: Remove all loose and peeling
paint and all other foreign substances. Clean any dirt and
grease by scrubbing the surface with a detergent and water
solution, followed by a thorough rinsing with clean water.
Set nails and ll holes, scratches, and gouges with
the appropriate wood ller and let dry completely.
Remove all dust with a tack or wiping cloth.
Fill all gaps with a 100% acrylic, siliconized, paintable
caulking, and allow to completely dry prior to coating.
Glossy Surfaces: For maximum adhesion, sand the
surface thoroughly before coating.
Wood: WARNING! Sanding or scraping pressure treated
lumber may be hazardous; wear appropriate protection.
New Plaster: New plaster should be thoroughly dried
out and cured for a minimum of 30 days before painting.
When cured, clean using a mixed solution of one part
vinegar and one part water to remove eorescence and
neutralize.Previously Painted Plaster: Remove all
loose and peeling paint and all other foreign substances.
Clean any dirt and grease by scrubbing the surface with
a detergent and water solution, followed by a thorough
rinsing with clean water. Set nails and ll holes, scratches,
and gouges with the appropriate spackling material and
let dry completely and sand smooth. Remove all dust with
a tack or wiping cloth. Fill all gaps with a 100% acrylic,
siliconized, paintable caulking, and allow to completely dry
prior to coating. Glossy Surfaces: For maximum adhesion,
sand the surface thoroughly before coating.
Stainblocking: After priming, test for stain bleed-through
by applying the topcoat to a small section. If the stain
bleeds through the topcoat, apply a second coat of
primer and test again before top-coating the entire area.
If bleeding continues, a longer dry time of the primer
may be needed before top-coating.
Masonry: All masonry surfaces must be cured at least
30 days before painting. The pH must be 10.0 or lower
prior to coating. Smooth masonry may require an adequate
prole for adhesion. For all other smooth trowel concrete,
create a prole using a product such as a muriatic acid
etcher or with mechanical means. Remove all loose
aggregate and debris.
COMPLIES WITH THE BELOW AS OF 12/1/2016
SCAQMD YES LEED v.4
†
YES
CARB YES MPI# 53,143
OTC YES MPI X-GREEN 53,143
LADCO YES GREENGUARD® YES
AIM YES CHPS YES
LEED v.3 (2009)
†
YES NAHB/ICC NGBS YES
This coating conforms to USDA regulatory requirements for
incidental food-contact materials intended for use on surfaces
not in direct contact with food, such as walls, oors and ceilings.
†
Please visit www.usgbc.org/LEED for additional details.
GREENGUARD is a registered trademark of UL Company.