TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2015 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
††
GREENGUARD is a registered trademark of UL Company.
*For as long as you reside in your home. See label for details.
Revised 1/2016
2 of 2
Metals: Ferrous and Non-Ferrous Metals: All metals
should be clean and free of any oils, rust, mill scale or other
contaminants. All metals require sucient “tooth” or prole
for optimum adhesion and therefore require some
type of sanding, abrasion, or chemical etching.
Oil lms: (especially on new or non-ferrous metals) should
be removed by scrubbing the surface with a detergent
and water solution, and thoroughly rinsed. Rust and Mill
Scale: Remove all rust and mill scale using sandpaper,
steel wool, abrasive blasting, or other abrading methods.
Prole: For best adhesion results, sand all metal surfaces
(including new ones) with sandpaper, steel wool, or etch
using a product muriatic acid. Clean by scrubbing the surface
with a detergent and water solution, followed by a thorough
rinsing with clean water. All ferrous metals must be primed
the same day it is cleaned to prevent rust.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD or
visit www.epa.gov/lead.
RECOMMENDED PRIMER/SYSTEMS:
PROPERLY PREPARED NEW SURFACES:
Wood: Composition Panels/Siding, Fiber Board
• BEHR PREMIUM PLUS® Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Wood: Cedar, Redwood, Shakes & Shingles
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Tannin/Stainblocking:
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Masonry: Stucco, Cinder Block, Cut Masonry Unit’s
(CMUs), Split Face Block
• BEHR PREMIUM Interior/Exterior Basement & Masonry
Waterproofer No. 875 (can also be used as a block ller.)
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Masonry: Cement Composition Panels/Siding,
Exterior Insulation and Finish Systems (EIFS)
or Synthetic Stucco
• BEHR PREMIUM Interior/Exterior Basement & Masonry
Waterproofer No. 875 (can also be used as a block ller.)
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Masonry with pH Levels up to 13.0:
• BEHR PREMIUM Interior/Exterior Basement & Masonry
Waterproofer No. 875
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
Ferrous and Non-Ferrous Metals:
• BEHR PREMIUM PLUS Interior/Exterior Multi-Surface
Primer & Sealer No. 436
PREVIOUSLY PAINTED SURFACES:
• Use a full coat or spot prime with BEHR PREMIUM PLUS
Interior/Exterior Multi-Surface Primer & Sealer No. 436.
TEST SPECIFICATIONS:
Scrubbability:
ASTM D2486 Scrub > 2500 (no shim)
Biological Growth:
ASTM D3273 (4 weeks) – Pass
Accelerated Weathering:
ASTM D4587, 500 hrs. exposure - Pass
CLEAN UP:
Clean all tools and equipment with clean water. For disposal
of empty containers and unused product, contact your
household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Do not use on oors.
• For best results, apply at temperatures between
35°F - 90°F. Temperatures above 90°F may aect
the application such as drying too fast, whereas
temperatures less than 35°F can cause slow drying
or prevent proper lm formation.
• Avoid heavy trac for 24 hours.
• Allow four weeks before washing or cleaning for full cure.
• Shelf life under normal conditions is two years unopened.
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Wear protective
clothing, gloves, eye, and face protection. Do not eat, drink,
or smoke when using this product. Take o contaminated
clothing and wash it before reuse. Wash hands thoroughly
after handling. Dispose of unused contents, container and
other contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for
several minutes and remove contacts if present and easy
to do. Continue rinsing and get medical attention if eye
irritation persists. If on skin: Wash with plenty of soap
and water. If swallowed: Rinse mouth and get medical
attention if you feel unwell.
EXTERIOR FLAT PAINT
NO. 4050 ULTRA PURE WHITE®