TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2015 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 11/2015
®
1 of 1
TEXTURED DECKOVER® SOLID COLOR COATING
NO. 5005
PRODUCT INFORMATION
BEHR PREMIUM Textured DECKOVER® Coating is an innovative , waterproong solid color coating that will bring your old,
weathered wood or concrete back to life. The advanced 100% acrylic resin creates a durable coating on your tired deck,
rejuvenating its look. Textured DECKOVER Coating is designed to conceal splinters & cracks up to 1/4" and creates a textured,
slip-resistant nish. It is available in a selection of popular wood and concrete custom colors.
RECOMMENDED USES:
Recommended for properly prepared interior and exterior weathered or cracked horizontal and vertical surfaces such as:
• Wood
• Composite
• Concrete
Do not use on drivable surfaces such as garage oors and driveways.
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 5005 116 oz./14 oz.
Resin Type: 100% Acrylic
Weight per Gallon: 11.5 lbs
% Solids by Volume: 51%
% Solids by Weight: 65%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 95-105 KU (Paste Paddle)
Recommended Film Thickness:
Wet: 21 mils Dry: 11 mils @ 75 Sq. Ft./Gal.
per 2 coats (5.5 mils Dry per coat)
Coverage: 75 Sq. Ft./Gal. 2 coats required.
APPLICATION:
Brush: Nylon/polyester brush
Roller: 1/4"- 1/2" nap
DO NOT USE WITH AIRLESS SPRAYER
Dry Time: @ 77° & 50% RH
To Recoat: 4-6 hours
Light Foot Trac: 24-48 hours
Full Cure: 72 hours
• For nail holes and cracks up to 1/4", completely ll in with
DECKOVER Coating using a nylon/polyester brush and allow
to dry prior to rolling. Deep nail holes and cracks may
require additional lling.
• Use pressure while rolling and apply generously.
• Avoid painting if humidity is expected to be greater than 80%
• 2 coats required
SURFACE PREPARATION:
The following steps and products are required:
(Proper surface preparation is required.) Exterior Wood
Surfaces: Replace rotting or unstable boards and remove
loose splinters. For exterior failing coatings or to remove
loose wood bers, use a product such as BEHR PREMIUM®
No. 64 Wood Stain & Finish Stripper followed by
BEHR PREMIUM No. 63 All-In-One Wood Cleaner to
neutralize the wood. When No. 64 is not needed, a product
such as No. 63 MUST be used to remove mill glaze and
clean the exterior wood surface. After using either No. 64
or No. 63, rinse thoroughly with a garden hose or pressure
washer. When rinsing with a pressure washer, use the
broadest spray pattern while keeping the nozzle at least
24" away from the surface. Allow the area to dry at least
24 hours before coating. Lightly sand to remove
remaining wood bers/fuzz.
Concrete Surfaces: Avoid areas that are structurally
weak or subject to hydrostatic pressure above 8 psi.
Allow new surfaces to cure for 30 days. Use a product such as
BEHR PREMIUM No. 992 Concrete & Masonry Paint Stripper
to strip peeling coating. Use a product such as
BEHR PREMIUM No. 991 Concrete & Masonry Cleaner & Etcher
to clean and etch uncoated concrete or No. 990 Concrete
& Masonry Degreaser & Cleaner on sound, coated
surfaces prior to coating. See behr.com for additional
product information.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or log on
to www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with clean water. For proper
disposal of empty containers and unused product, contact
your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing
• Do not use without the addition of tinting colorants
• Do not use if rain is expected within 24 hours
• DO NOT THIN PRODUCT
• Avoid applying paint in direct sunlight or hot surfaces
• Test product for color on a small hidden area
before proceeding
• Painted surfaces may become slippery when wet
• Shelf life under normal conditions is two years
(unopened containers)
• Do not use on drivable surfaces such as garage oors
and driveways
• Temperature Range: 50-90°F (10-32°C)
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Wear protective
clothing, gloves, eye, and face protection. Do not eat, drink,
or smoke when using this product. Take o contaminated
clothing and wash it before reuse. Wash hands thoroughly
after handling. Dispose of unused, contents, container and
other contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for several
minutes and remove contacts if present and easy to do.
Continue rinsing and get medical attention if eye irritation
persists. If on skin: Wash with plenty of soap and water.
If swallowed: Rinse mouth and get medical attention
if you feel unwell.
COMPLIES WITH THE BELOW AS OF 3/1/2015
SCAQMD YES LADCO YES
CARB YES AIM YES
LEED v.3 (2009)
†
YES MPI# 127
OTC YES FLAME SPREAD/CLASS A YES