TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2017 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 6/2017
1 of 2
EXTERIOR ELASTOMERIC MASONRY, STUCCO & BRICK PAINT
NO. 68 WHITE
COMPLIES WITH THE BELOW AS OF 6/1/2017
SCAQMD YES LEED v.3 (2009)
†
YES
CARB YES LEED v.4
†
YES
OTC YES GREENGUARD® YES
LADCO YES MPI 40
AIM YES
†
Please visit www.usgbc.org/LEED for additional details.
GREENGUARD is a registered trademark of UL Company.
PRODUCT INFORMATION
BEHR PREMIUM® Elastomeric Masonry, Stucco & Brick Paint is a exible, high-build coating designed to expand and contract, bridging
hairline cracks in exterior, vertical masonry surfaces. This waterproong coating is extremely durable and is mildew and dirt resistant.
It has superior elasticity and elongation properties, stretching up to 600%. This 100% acrylic latex formula provides a breathable lm,
releasing moisture vapor that builds in walls. This low-sheen paint has excellent color retention and is available in 55 custom tinted colors.
RECOMMENDED USES:
This product is ideal for use on properly prepared and primed vertical surfaces such as:
• Concrete Tilt-Up • Concrete Block/CMU • Cement Board Siding
• Brick • Stucco • EIFS
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 68 124 oz. / 6 oz.
No. 67 116 oz. / 14 oz.
Gloss: <10 @ 60°
Sheen: 0-6 @ 85°
Resin Type: 100% Acrylic
Weight per Gallon: 10.9 lbs.
% Solids by Volume: 48.0%
% Solids by Weight: 60.4%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 120-135 KU
Recommended Film Thickness:
Wet: 21.3 mils / Dry: 10.2 mils @ 75 Sq. Ft./Gal.
Wet: 12.8 mils / Dry: 6.1 mils @ 125 Sq. Ft./Gal.
Coverage: 75-125 Sq. Ft./Gal. depending on application
method and substrate porosity. Does not include the loss
of material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/4"-1 1/4" Nap
Airless Spray: At packaged consistency
Tip: .025"- .029"
Filter: 60 mesh
Thinning: Do Not Thin
Dry Time: @ 77° & 50% RH
Longer dry time may be required in cooler temperatures
and higher humidity.
To Touch: 4-6 hours
To Recoat: 24 hours
Full Cure: 2 weeks
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease, wax,
polish, mold and mildew stains, loose and peeling paint, rust,
and all other foreign substances.
Stainblocking: After priming, test for stain bleedthrough
by applying the topcoat to a small section. If the stain bleeds
through the topcoat, apply a second coat of primer and test
again before top-coating the entire area. If bleeding
continues, a longer dry time of the primer may be needed
before top-coating.
Masonry: All masonry surfaces must be cured at least 30 days
before painting. The pH must be 10.0 or lower prior to coating.
Smooth masonry may require an adequate prole for adhesion.
For all other smooth concrete, create a prole using a product
such as a muriatic acid etcher to achieve a textured prole.
Use a cleaner to remove loose aggregate and debris.
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD or
visit www.epa.gov/lead.
RECOMMENDED PRIMER/SYSTEMS:
PROPERLY PREPARED NEW SURFACES:
Masonry:
• BEHR PREMIUM PLUS® Interior/Exterior Water-Based Primer
& Sealer No. 436
Masonry with pH Levels up to 13.0:
• BEHR PREMIUM PLUS Interior/Exterior Water-Based Primer
& Sealer No. 436
• KILZ KLEAR® Interior/Exterior Water-Based Primer
New Surfaces:
• All surfaces must be clean, free of dust, chalk, oil, grease, wax,
polish, mold and mildew stains, loose and peeling paint, rust
and all other foreign substances.
PREVIOUSLY PAINTED SURFACES:
• Use a full coat or spot prime with BEHR PREMIUM PLUS®
Interior/Exterior Water-Based Primer & Sealer No. 436
on properly prepared surfaces.
TEST SPECIFICATIONS:
Scrubbability:
ASTM D2486, Scrub > 500
Accelerated Weathering:
ASTM D4587, 1000 hrs. exposure - Pass
Flexibility:
ASTM D522, method B - Pass
Biological Growth:
ASTM D3273 (4 weeks) – Pass
Tensile Strength, Elongation and Recovery:
ASTM D2370, Elongation > 600%
ASTM D2370, Tensile Strength >200 psi
Low Temperature Flexibility:
ASTM D1737 – Pass
Resistance Wind Driven Rain:
ASTM D6904/TT-C-555B - Pass:
Apply 2 coats at min. 6.1 mils DFT for a min.
12.2 mils total system DFT.
Water Vapor Permeability:
Test Method:
ASTM E96, Water Method
Result - 25 US Perms
CLEAN UP:
Clean all tools and equipment with clean water. For disposal of
empty containers and unused product, contact your household
refuse collection service.