TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2019 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 7/2019
2 of 2
Glossy Surfaces: For maximum adhesion, sand the surface
thoroughly to provide a rough surface before coating.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
SYSTEM RECOMMENDATIONS:
Drywall/Wallboard:
• 1 coat BEHR® Kitchen, Bath & Trim Interior Stain-Blocking
Primer & Sealer No. 75
2 coats BEHR Urethane Alkyd Interior/Exterior Enamel
Plaster:
• 1 coat BEHR Kitchen, Bath & Trim Interior Stain-Blocking
Primer & Sealer No. 75 or BEHR Multi-Surface Interior/
Exterior Stain-Blocking Primer & Sealer No. 436
(recommended for surfaces with pH level of up to 13)
2 coats BEHR Urethane Alkyd Interior/Exterior Enamel
Masonry: Concrete, Cement, Brick, Stucco, EIFS:
• 1 coat BEHR Multi-Surface Interior/Exterior Stain-Blocking
Primer & Sealer No. 436
2 coats BEHR Urethane Alkyd Interior/Exterior Enamel
Concrete Masonry Units: Concrete Block,
Cinder Block, Split-Face Block:
• 1 coat BEHR DRYPLUS® Masonry Waterproofer No. 875
2 coats BEHR Urethane Alkyd Interior/Exterior Enamel
Fiber-Cement:
• 1 coat BEHR Multi-Surface Interior/Exterior Stain-Blocking
Primer & Sealer No. 436
2 coats BEHR Urethane Alkyd Interior/Exterior Enamel
Wood:
• 1 coat BEHR Kitchen, Bath & Trim Interior Stain-Blocking
Primer & Sealer No. 75 (interior only) or BEHR Multi-
Surface Interior/Exterior Stain-Blocking Primer & Sealer
No. 436 (recommended for tannin-rich woods)
2 coats BEHR Urethane Alkyd Interior/Exterior Enamel
Ferrous Metal:
• 1 coat BEHR Interior/Exterior Metal Primer No. 435
(recommended for optimal corrosion resistance) or BEHR
Multi-Surface Interior/Exterior Stain-Blocking Primer &
Sealer No. 436
2 coats BEHR Urethane Alkyd Interior/Exterior Enamel
Non-Ferrous Metal:
• 1 coat BEHR Interior/Exterior Metal Primer No. 435
(recommended for optimal corrosion resistance) or BEHR
Multi-Surface Interior/Exterior Stain-Blocking Primer &
Sealer No. 436
2 coats BEHR Urethane Alkyd Interior/Exterior Enamel
Vinyl, PVC, Fiberglass, Architectural Plastics:
• 1 coat BEHR Interior/Exterior Bonding Primer No. 432
or BEHR Multi-Surface Interior/Exterior Stain-Blocking
Primer & Sealer No. 436
2 coats BEHR Urethane Alkyd Interior/Exterior Enamel
Note: Do not paint vinyl with a color darker than the
original to prevent potential warping due to heat
absorption. For other plastic composites, dark colors
should be applied with caution where the surface may
be exposed to sunlight which may cause distortion of the
plastic.
CLEANUP/DISPOSAL:
Clean all tools and equipment with warm, soapy water. Do
not dispose of this product down a drain. If spilled, contain
material and remove with an inert absorbent. Dispose of
contaminated absorbent, container and unused product
in accordance with all current federal, state and local
regulations. For recycling or disposal of empty containers,
unused product and soiled rags, contact your household
refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• For above-grade surfaces only.
• Do not use on oors.
• For best results, apply when air, material and surface
temperatures are between 50°F and 90°F. Do not apply in
direct sunlight. Temperatures above 90°F can cause the
paint to dry too fast, whereas temperatures below 50°F
can inhibit proper lm formation.
• Cover unused product to help prevent skinning.
• Allow 7 days before washing or cleaning for full cure.
• Shelf life under normal conditions is 2 years unopened.
GENERAL INFORMATION:
CAUTION IRRITANT MAY CAUSE EYE, NOSE AND THROAT
IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND
AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE
PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH
ADEQUATE VENTILATION. To avoid breathing vapors and
spray mist, open windows and doors or use other means to
ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase
fresh air. If properly used, a respirator (NIOSH approved for
organic vapor with P series particulate pre-lter) may oer
additional protection; obtain professional advice before
using. A dust mask does not provide protection against
vapors. Avoid contact with eyes and skin. Wash thoroughly
after handling. Close container after each use.
FIRST AID: If you experience diculty in breathing,
leave the area to obtain fresh air. If continued diculty is
experienced, get medical assistance immediately. In case of
eye contact, ush immediately with plenty of water for at
least 15 minutes and get medical attention; for skin, wash
thoroughly with soap and water. If swallowed, get medical
attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN – DO NOT
TAKE INTERNALLY.
INTERIOR/EXTERIOR URETHANE ALKYD SEMIGLOSS ENAMEL
NO. 3900 WHITE