TDS

TECHNICAL DATA SHEETTECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative,
call 1-800-854-0133 Ext. 2 (U.S.A. only) or visit behr.com. ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 2/2020
1 of 2
SOLID COLOR WATERPROOFING STAIN & SEALER
NO. 5011 TINTABLE WHITE BASE
PRODUCT INFORMATION
BEHR PREMIUM® SOLID COLOR WATERPROOFING STAIN & SEALER is a 100% acrylic formula that seals out the elements, and sun’s
harmful UV rays, for up to 10 years on decks and up to 25 years on fences & siding. It forms a highly durable and mildew resistant
nish which resists scung, cracking, peeling, and blistering.
RECOMMENDED USES:
Ideal for use on properly prepared new to moderately weathered, unsealed exterior surfaces such as:
• Wood • Wood Composite
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 5011 Tintable White Base 124  oz / 6  oz
No. 5013 Deep Base 116  oz / 14  oz
Pre-Mixed Colors:
No. 50533 Cedar Naturaltone
No. 50129 Chocolate
No. 50330 Redwood
No. 50117 Russet
No. 50104 Cordovan Brown
Resin Type: 100% Acrylic
Weight per Gallon: 10.4 lb
% Solids by Volume: 38% ± 2%
% Solids by Weight: 50% ± 2%
VOC: <100 g/L
Flash Point: N/A
Viscosity: 68-77 KU
Recommended Film Thickness:
Wet: 8.0 mils / Dry: 3.0 mils @ 200 sq ft/gal
Wet: 4.0 mils / Dry: 1.5 mils @ 400 sq ft./gal
Coverage: 200-400 sq ft/gal, depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8" nap roller cover
For best results, a pad applicator is recommended over large
deck areas.
Airless Spray:
Tip: .015"-.019"
Filter: 60 mesh
Fluid Pressure: 1,400 – 2,400 psi
Follow spraying immediately with a pad, back brushing or
back rolling for a uniform appearance.
Thinning: If thinning is required, thin with water at a rate
of no more than 1/2 pint per gallon.
Dry Time: @ 77°F & 50% RH
To Recoat: 1-2 hours
Light Foot Trac: 24-48 hours
Full Cure: 72 hours
Dry times are temperature, humidity, and lm thickness
dependent.
• Work in small sections lightly saturating the surface and
immediately back-brush or use pad applicator to eliminate
puddling; remove excess and evenly distribute the nish.
Maintain a wet edge when applying.
SURFACE PREPARATION:
The following steps and products are recommended
for best results: If you use a product such as
BEHR PREMIUM Wood Stain & Finish Stripper No. 64 to
remove loose wood bers, latex, oil-based and 100%
acrylic coatings on new weathered wood, then you must
use a product such as BEHR PREMIUM All-In-One Wood
Cleaner No. 63 to clean, brighten & neutralize wood. If you
do not use a product such as BEHR PREMIUM Wood Stain
& Finish Stripper No. 64, then use a product such as BEHR
PREMIUM All-In-One Wood Cleaner No. 63 to clean and
brighten the wood surface and to remove light to medium
stains caused by mold, mildew, algae & fungus. Rinse
thoroughly and allow to dry before coating. On new wood,
use a product such as BEHR PREMIUM All-In-One Wood
Cleaner No. 63 to remove mill glaze and open the pores of
the wood. Lightly sand to remove remaining wood bers/
fuzz.
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved
respirator to control lead exposure. Clean up carefully with
a HEPA vacuum and a wet mop. Before you start, nd out
how to protect yourself and your family by contacting the
National Lead Information Center at 1-800-424-LEAD or
log on to www.epa.gov/lead.
SYSTEM RECOMMENDATIONS:
Wood & Tannin/Stain-blocking:
• BEHR PREMIUM PLUS® Exterior Multi-Surface Primer
& Sealer No. 436
PREVIOUSLY PAINTED SURFACES:
• Use a full coat or spot prime with BEHR PREMIUM PLUS
Exterior Multi-Surface Primer & Sealer No. 436 on properly
prepared surfaces.
CLEANUP/DISPOSAL:
Clean all tools and equipment with warm, soapy water. Do
not dispose of this product down a drain. If spilled, contain
material and remove with an inert absorbent. Dispose of
contaminated absorbent, container and unused product
in accordance with all current federal, state and local
regulations. For recycling or disposal of empty containers,
unused product and soiled rags, contact your household
refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• For best results, apply when air, material and surface
temperatures are between 35°F and 90°F. When the air
temperature is at 35°F, substrates may be colder; prior to
painting, check to be sure the air, surface, and material
temperatures are above 35°F and at least 5°F above the
dew point. Avoid using if rain or snow is expected within
24 hours. Do not apply at air or surface temperatures
below 35°F or when air or surface temperatures may
drop below 35°F within 48 hours. Do not apply in direct
sunlight. Temperatures above 90°F can cause the paint to
dry too fast.
• Always test product on an inconspicuous area before
proceeding with entire project.
• Over application of stain will lead to surface failure
including peeling & cracking.
• Stained surfaces may become slippery when wet.
• Shelf life under normal conditions is 2 years unopened.
COMPLIES WITH THE BELOW AS OF 2/1/2020
SCAQMD YES OTC YES
CARB SCM 2007 YES LADCO YES
CARB YES AIM YES
OTC Phase II YES MPI# 16