TDS
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2014 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 11/2015
1 of 1
TRANSPARENT WEATHERPROOFING ALLINONE WOOD FINISH
NO. 500
PRODUCT INFORMATION
BEHR PREMIUM® Transparent Weatherproong All-In-One Wood Finish has a 100% acrylic formula that seals out the elements
and the sun’s harmful UV rays on decks, fences and siding. It’s available in 3 pre-mixed colors as well as 6 custom colors so you can
get the look you want while preserving your valuable investment.
RECOMMENDED USES:
Recommended for properly prepared new to moderately weathered, unsealed exterior wood surfaces such as:
• Wood
• Plywood
• Pressured Treated Lumber
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 500 Natural 124 oz. / 4 oz.
Pre-Mixed Colors:
No. 500 Natural
No. 501 Cedar Naturaltone
No. 502 Redwood
Resin Type: Advanced 100% Acrylic
Weight per Gallon: 8.7 lbs
% Solids by Volume: 25.8%
% Solids by Weight: 28.0%
VOC: <275 g/L
Flash Point: N/A
Viscosity: 15-30 sec #2 Zahn Cup
Recommended Film Thickness:
Wet: 5.4 Dry: 1.4 mils @ 300-350 Sq.Ft./Gal.
Wet: 2.7 Dry: 0.7 mils @ 600 Sq.Ft./Gal.
Coverage: 300-600 Sq.Ft./Gal., depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8" nap
Pad Applicator
Airless Spray: At packaged consistency
Tip: .015"-.019"
Filter: 60 mesh
Dry Time: @ 77° & 50% RH
To Recoat: 1-2 hours
Light Foot Trac: 24-48 hours
Full Cure: 72 hours
• Follow spraying immediately with a pad, back brushing or
back rolling for a uniform appearance.
• Work in small sections lightly saturating the surface
and immediately back-brush or use pad applicator to
eliminate puddling; remove excess and evenly distribute
the nish. Maintain a wet edge when applying.
SURFACE PREPARATION:
The following steps and products are recommended
for best results: If you use a product such as
BEHR PREMIUM Wood Stain & Finish Stripper No. 64 to
remove loose wood bers, latex, oil-based and 100%
acrylic coatings on new weathered wood, then you must
use a product such as BEHR PREMIUM All-In-One Wood
Cleaner No. 63 to clean, brighten & neutralize wood. If you
do not use a product such as BEHR PREMIUM Wood Stain
& Finish Stripper No. 64, then use a product such as
BEHR PREMIUM All-In-One Wood Cleaner No. 63 to clean
and brighten the wood surface and to remove light to
medium stains caused by mold, mildew, algae & fungus.
On new wood, use a product such as BEHR PREMIUM
All-In-One Wood Cleaner No. 63 to remove mill glaze and
open the pores of the wood. Rinse thoroughly and allow
to dry before coating. Lightly sand to remove remaining
wood bers/fuzz.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. Contact the National Lead
Information Center at 1-800-424-LEAD or log on
to www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with clean water. For proper
disposal of empty containers and unused product, contact
your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing
• Do not use if rain is expected within 24 hours
• DO NOT THIN PRODUCT
• Avoid applying stain in direct sunlight or to hot surfaces
• Test product for color on a small hidden area
before proceeding
• Over application of stain will lead to surface failure
including peeling & cracking
• Stained surfaces may become slippery when wet.
• Shelf life under normal conditions is two years
(unopened containers)
• Temperature Range: 40-90°F
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Harmful if
swallowed. Wear protective clothing, gloves, eye, and face
protection. Do not eat, drink, or smoke when using this
product. Take o contaminated clothing and wash it
before reuse. Wash hands thoroughly after handling.
Collect spillage and avoid release to the environment.
Dispose of unused, contents, container and other
contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for several
minutes and remove contacts if present and easy to do.
Continue rinsing and get medical attention if eye irritation
persists. If on skin: Wash with plenty of soap and water.
If swallowed: Rinse mouth and get medical attention
if you feel unwell.
COMPLIES WITH THE BELOW AS OF 9/1/2014
SCAQMD YES LADCO YES
CARB YES AIM YES
OTC YES LEED v.3 (2009)
†
YES
FLAME SPREAD/CLASS A
YES