TDS
TECHNICAL DATA SHEETTECHNICAL DATA SHEET
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other nature
are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative, call 1-800-854-
0133 Ext. 2 (U.S.A. only) or visit behr.com. ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 2/2020
1 of 2
SEMITRANSPARENT WATERPROOFING STAIN & SEALER
NO. 5077 TINT BASE
PRODUCT INFORMATION
BEHR PREMIUM® SEMI-TRANSPARENT WATERPROOFING STAIN & SEALER is a 100% acrylic formula that seals out the elements, and
sun’s harmful UV rays, for up to 6 years on decks and up to 8 years on fences & siding. It’s available in a curated collection of 60
color choices to help you create a look that’s as beautiful as it is durable.
RECOMMENDED USES:
Ideal for use on properly prepared new to moderately weathered, unsealed exterior wood surfaces (0-10 years exposure)
such as:
• Wood • Engineered (Synthetic) Wood • Pressured Treated Lumber
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 5077 Tint base 120 oz / 8 oz
Pre-Mixed Colors:
No. 5330 Redwood
No. 5533 Cedar Naturaltone
No. 5129 Chocolate
No. 5117 Russet
No. 5104 Cordovan Brown
Resin Type: Advanced 100% Acrylic
Weight per Gallon: 8.6 lb
% Solids by Volume: 25% ± 2%
% Solids by Weight: 27% ± 2%
VOC: <100 g/L
Flash Point: N/A
Viscosity: 15-30 sec #2 Zahn Cup
Recommended Film Thickness:
Wet: 5.3 mils / Dry: 1.3 mils @ 300 sq ft/gal
Wet: 3.2 mils / Dry: 0.8 mils @ 500 sq ft/gal
Coverage: 300-500 sq ft/gal. Apply rst coat at a spread
rate of 300 sq ft/gal. Apply a thinner second coat at a spread
rate of 500 sq ft/gal. Two coats are required for optimal
appearance and durability.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8" nap roller cover
For best results, a pad applicator is recommended over large
deck areas.
Airless Spray:
Tip: .015"-.019"
Filter: 60 mesh
Fluid Pressure: 1,400 – 2,400 psi
Follow spraying immediately with back brushing or back
rolling for a uniform appearance.
Thinning: DO NOT THIN PRODUCT
Dry Time: @ 77°F & 50% RH
To Recoat: 1-2 hours
Light Foot Trac: 24-48 hours
Full Cure: 72 hours
Dry times are temperature, humidity, and lm thickness
dependent.
Work in small sections lightly saturating the surface and
immediately back-brush or use pad applicator to eliminate
puddling; remove excess and evenly distribute the nish.
Maintain a wet edge when applying.
SURFACE PREPARATION:
The following steps and products are recommended
for best results: If you use a product such as BEHR
PREMIUM® Wood Stain & Finish Stripper No. 64 to remove
loose wood bers, latex, oil-based and 100% acrylic
coatings on new weathered wood, then you must use a
product such as BEHR PREMIUM® All-In-One Wood Cleaner
No. 63 to clean, brighten & neutralize wood. If you do not
use a product such as BEHR PREMIUM Wood Stain & Finish
Stripper No. 64, then use a product such as BEHR PREMIUM
All-In-One Wood Cleaner No. 63 to clean and brighten the
wood surface and to remove light to medium stains caused
by mold, mildew, algae & fungus. Rinse thoroughly and
allow to dry before coating. On new wood, use a product
such as BEHR PREMIUM All-In-One Wood Cleaner No. 63 to
remove mill glaze and open the pores of the wood. Lightly
sand to remove remaining wood bers/fuzz.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEANUP/DISPOSAL:
Clean all tools and equipment with warm, soapy water.
Do not dispose of this product down a drain. If spilled,
contain material and remove with an inert absorbent.
Dispose of contaminated absorbent, container and unused
product in accordance with all current federal, state
and local regulations. For recycling or disposal of empty
containers, unused product and soiled rags, contact your
household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing
• For best results, apply when air, material and surface
temperatures are between 40°F and 90°F. Avoid applying
stain in direct sunlight or to hot surfaces. Temperatures
above 90°F can cause the paint to dry too fast. Do not
apply if rain is expected within 24 hours of product
application.
• Always test product on an inconspicuous area before
proceeding with entire project.
• Over application of stain will lead to surface failure
including peeling & cracking
• Stained surfaces may become slippery when wet.
• Shelf life under normal conditions is 2 years unopened.
COMPLIES WITH THE BELOW AS OF 2/1/2020
SCAQMD YES OTC YES
CARB SCM 2007 YES LADCO YES
CARB YES AIM YES
OTC Phase II YES