TDS
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2017 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 2/2017
1 of 1
SEMITRANSPARENT WATERPROOFING STAIN & SEALER
NO. 5077
PRODUCT INFORMATION
BEHR PREMIUM® SEMI-TRANSPARENT WATERPROOFING STAIN & SEALER is a 100% acrylic formula that seals out the elements, and
sun’s harmful UV rays, for up to 6 years on decks and up to 8 years on fences & siding. It’s available in 60 custom colors to help you
create a look that’s as beautiful as it is durable.
RECOMMENDED USES:
Recommended for properly prepared new to moderately weathered, unsealed exterior wood surfaces
(0-10 years exposure) such as:
• Wood
• Engineered (Synthetic) Wood
• Pressured Treated Lumber
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 5077 Tint base 120 oz. / 8 oz.
Pre-Mixed Colors:
No. 5330 Redwood
No. 5533 Cedar Naturaltone
No. 5129 Chocolate
No. 5117 Russet
No. 5104 Cordovan Brown
Resin Type: Advanced 100% Acrylic
Weight per Gallon: 8.6 lbs
% Solids by Volume: 25.4%
% Solids by Weight: 2 7. 2 %
VOC: <100 g/L
Flash Point: N/A
Viscosity: 15-30 sec #2 Zahn Cup
Recommended Film Thickness:
Wet: 6.4 Dry: 1.6 mils @ 300 Sq. Ft./Gal.
Wet: 3.2 Dry: 0.8 mils @ 500 Sq. Ft./Gal.
Coverage: 250-300 Sq. Ft./Gal. Apply a thinner second coat
at aspread rate of approximately 500- 600 Sq. Ft./Gal. 2
coats are required for optimal appearance and durability.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8" nap
Pad Applicator
Airless Spray: At packaged consistency
Tip: .015"-.019"
Filter: 60 mesh
Dry Time: @ 77°F & 50% RH
To Recoat: 1-2 hours
Light Foot Trac: 24-48 hours
Full Cure: 72 hours
• Follow spraying immediately with a pad, back brushing or
back rolling for a uniform appearance.
• Work in small sections lightly saturating the surface and
immediately back-brush or use pad applicator to eliminate
puddling; remove excess and evenly distribute the nish.
• Maintain a wet edge when applying.
SURFACE PREPARATION:
The following steps and products are recommended
for best results: If you use a product such as
BEHR PREMIUM® Wood Stain & Finish Stripper No. 64 to
remove loose wood bers, latex, oil-based and 100%
acrylic coatings on new weathered wood, then you must use
a product such as BEHR PREMIUM® All-In-One Wood Cleaner
No. 63 to clean, brighten & neutralize wood. If you do not
use a product such as BEHR PREMIUM Wood Stain & Finish
Stripper No. 64, then use a product such as BEHR PREMIUM
All-In-One Wood Cleaner No. 63 to clean and brighten the
wood surface and to remove light to medium stains caused
by mold, mildew, algae & fungus. Rinse thoroughly and
allow to dry before coating. On new wood, use a product
such as BEHR PREMIUM All-In-One Wood Cleaner No. 63
to remove mill glaze and open the pores of the wood.
Lightly sand to remove remaining wood bers/fuzz.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or log on
to www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with clean water. For proper
disposal of empty containers and unused product, contact
your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing
• Do not use without the addition of tinting colorants
• Do not use if rain is expected within 24 hours
• DO NOT THIN PRODUCT
• Avoid applying stain in direct sunlight or hot surfaces
• Test product for color on a small hidden area
before proceeding
• Over application of stain will lead to surface failure
including peeling & cracking
• Stained surfaces may become slippery when wet.
• Shelf life under normal conditions is two years
(unopened containers)
• Temperature Range: 35-90°F
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Harmful if
swallowed. Wear protective clothing, gloves, eye, and
face protection. Do not eat, drink, or smoke when using
this product. Take o contaminated clothing and wash
it before reuse. Wash hands thoroughly after handling.
Collect spillage and avoid release to the environment.
Dispose of unused, contents, container and other
contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for
several minutes and remove contacts if present and easy
to do. Continue rinsing and get medical attention if eye
irritation persists. If on skin: Wash with plenty of soap
and water. If swallowed: Rinse mouth and get medical
attention if you feel unwell.
COMPLIES WITH THE BELOW AS OF 2/1/2017
SCAQMD YES OTC Phase II YES
CARB YES LADCO YES
CARB SCM 2007 YES AIM YES
OTC