TDS
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2016 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 2/2016
1 of 2
PORCH & PATIO PAINT & PRIMER IN ONE PAINT
NO. 6060 LOWLUSTRE ULTRA PURE WHITE®
PRODUCT INFORMATION
BEHR PREMIUM® Porch & Patio Paint & Primer In One Paint is a l00% acrylic latex product that has a mildew resistant nish,
resists scung, fading, cracking and peeling while providing a durable, long-lasting nish that is ideal for both interior and
exterior applications.
RECOMMENDED USES:
Use on previously painted or primed interior or exterior surfaces such as:
• Wood • Concrete • Composite
Not for use on garage oors or areas subject to automotive trac.
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 6060 126 oz. / 4 oz.
No. 6030 116 oz. / 14 oz.
PRE-MIXED COLORS:
No. 6095 Low-Lustre Slate Gray
Gloss: 5-15 @ 60°
Sheen: 5-15 @ 85°
Resin Type: 100% Acrylic Latex
Weight per Gallon: 10.7 lbs.
% Solids by Volume: 37%
% Solids by Weight: 49%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 90-100 KU
Recommended Film Thickness:
Wet: 8.0 Dry: 3.0 mils @ 200 Sq. Ft./Gal.
Wet: 4.0 Dry: 1.5 mils @ 400 Sq. Ft./Gal.
Coverage: Up to 400 sq. ft/gal. depending on application
method and substrate porosity. Does not include the loss
of material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8"-1/2" nap
Airless Spray: At packaged consistency
Tip: .015"- .021"
Filter: 60 mesh
Thinning: (If required) No more than 1/2 pint
of water per gallon.
Dry Time: @ 77° & 50% RH
Longer dry time may be required in cooler temperatures
and higher humidity.
To Touch: 1 hour
To Recoat: 4-6 hours
Allow 72 hours before subjection to normal use.
After 30 days, used paint lm may be cleansed
with a mild, non-abrasive liquid detergent.
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling
paint, rust and all other foreign substances.
Wood: Shakes & Shingles, Composition Panels/
Siding, Fiber Board. New Wood: Remove mill glaze
with sandpaper or use a product such as BEHR PREMIUM®
All-in-One Wood Cleaner No. 63 to open the pores of the
wood and follow all label instructions. Remove mildew
stains with a mildew stain removing product. Set nails and
ll holes, scratches, and gouges with the appropriate wood
ller and let dry completely. Remove all dust with a wiping
cloth. Fill all gaps with a 100% acrylic, siliconized, paintable
caulking and allow to dry completely. Patched and lled
surfaces should be sanded smooth and dusted clean prior to
coating. Previously Painted Wood: Remove all loose and
peeling paint and all other foreign substances. Clean any dirt
and grease by scrubbing the surface with a detergent and
water solution, followed by a thorough rinsing with clean
water. Set nails and ll holes, scratches, and gouges with
the appropriate wood ller and let dry completely prior to
coating. Remove all dust with a wiping cloth. Fill all gaps
with a 100% acrylic, siliconized, paintable caulking, and
allow to completely dry prior to coating. Glossy Surfaces:
For maximum adhesion, scu sand the surface thoroughly
before coating. Weathered Wood Surfaces: To remove
loose wood bers, latex, oil-based and 100% acrylic coatings
on new or weathered wood decks, siding, fences, shakes and
shingles, use a product such as BEHR PREMIUM® Wood Stain
& Finish Stripper No. 64 and follow all label instructions.
Use a product such as BEHR PREMIUM All-in-One Wood
Cleaner No. 63 and follow all label instructions to clean
and brighten the wood surface and to remove light to
medium stains caused by mold, mildew, algae and fungus.
Be sure to follow all label instructions.
Wood: WARNING! Sanding or scraping pressure treated
lumber may be hazardous; wear appropriate protection.
Tannin Bleed & Stainblocking: After priming, test for
stain bleed-through by applying the topcoat to a small
section. If the stain bleeds through the topcoat, apply a
second coat of primer and test again before top-coating
the entire area. If bleeding continues, a longer dry time
of the primer may be needed before top-coating or an
additional coat of primer may be required to block the
tannin bleed or stain.
Concrete: Stucco, Cut Masonry Unit’s (CMUs), Split-
Faced Block. New: All masonry surfaces must be cured at
least 30 days before painting. The pH must be 10.0 or lower
prior to coating. Smooth masonry may require an adequate
prole for adhesion. For all other smooth concrete, create a
prole using a product with mechanical means.
Concrete: Cement Composition Panels/Siding,
Exterior Insulation and Finish Systems (EIFS) or
Synthetic Stucco. New: All masonry surfaces must be
cured at least 30 days before painting. The pH must be 10.0 or
lower prior to coating. All surfaces must be clean, free of dust,
chalk, mold and mildew stains, loose and peeling paint and
all other foreign substances. Clean surfaces with a detergent
and water solution by scrubbing the surface vigorously and
rinse with a garden hose or a power washer at a low setting
(500-1200 PSI). DO NOT USE HIGH PRESSURE as this may harm
the substrate. Previously Painted Surface: All surfaces
must be clean, free of dust, chalk, oil, grease, mold and
mildew stains, loose and peeling paint and all other foreign
substances. Clean surfaces with a detergent and water
solution by scrubbing the surface vigorously and rinse with a
garden hose or a power washer and allow to dry.
Composite: All surfaces must be clean, free of dust, chalk,
mold and mildew stains, loose and peeling paint and all other
foreign substances. Clean surfaces with a detergent and
water solution by scrubbing the surface vigorously and rinse
with a garden hose or a power washer and allow to dry.
COMPLIES WITH THE BELOW AS OF 2/1/2016
SCAQMD YES LADCO YES
CARB YES AIM YES
OTC YES LEED v.3 (2009)
†
YES
†
Please visit www.usgbc.org/LEED for additional details.