Use and Care Manual

CAUTION! IRRITANT! HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN. Avoid
contact with eyes, skin and clothing. Do not breathe fumes. Wear eye protection and protective
clothing. Use only with adequate ventilation. FIRST AID TREATMENT: If swallowed, call a
Poison Control Centre or doctor immediately. Do not induce vomiting. If in eyes rinse with
water for 20 minutes. If on skin rinse well with water. If inhaled, move person to fresh air.
CAUTION: KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.
©2016 Behr Process Corporation
Santa Ana, CA 92704 U.S.A. • behr.com
V.O.C. (C.O.V.) <50 g/L • REV. 08/16
No. 6050-N Ultra Pure White
®
No. 6300 Deep Base
No. 6694 Silver Gray
No. 6695 Slate Gray
BEHR PREMIUM
®
Low-Lustre Enamel
Porch & Patio Floor Paint
• Resists Scuffing, Fading, Cracking and Peeling
• Mildew Resistant Finish
• 100% Acrylic Latex
• Low-Lustre Sheen
Spread Rate:
Rough 18-28 m
2
Smooth 28-37 m
2
Protect
from Freezing
Dry Time:
1 Hr. Dry to Touch
4-6 Hr. Recoat
Clean-Up:
Soap & Water
CAUTION: Painted surfaces may become slippery when wet.
Follow all label instructions.
WHERE TO USE
On properly prepared, previously painted or primed Interior/Exterior surfaces.
Ideal for Porches, Floors, Decks, Basement Floors, Patios, Siding, Trim, Furniture
and Trellises. Do not use on areas subject to automotive tires.
PREPARATION
†
(Proper surface preparation is required.) All surfaces must be clean, sound,
dry and free of any dirt, oil and grease. Remove mildew stains with a mildew
stain removing product. New or Weathered Wood: Use a product such as
BEHR PREMIUM
®
No. 63 All-In-One Wood Cleaner. Lightly sand to remove remaining
wood fibers/fuzz. Painted Surfaces-Wood: For a painted surface in sound condition,
use a product such as BEHR PREMIUM No. 63 All-In-One Wood Cleaner, to clean and
prepare the surface. If the coating is failing or peeling, use a paint stripper such as
BEHR PREMIUM No. 64 Wood Stain & Finish Stripper, to remove old coating.
Scuff sand glossy surfaces. Follow with BEHR PREMIUM No. 63 All-In-One Wood
Cleaner. Use stainless steel or galvanized nails to prevent nail staining. Countersink
nail heads, repair imperfections and sand smooth. Remove all dust with a damp
cloth, allow to dry. Uncoated Concrete or Masonry Surfaces: Allow new surfaces
to cure 30 days. Clean and etch surface using a product such as BEHR PREMIUM
No. 991 Concrete & Masonry Cleaner & Etcher to achieve a textured proile similar
to 150 grit sandpaper. Painted Surfaces-Concrete: For a painted surface in sound
condition, use a product such as BEHR PREMIUM No. 990 Concrete & Masonry
Degreaser & Cleaner to clean and prepare the surface. If the coating is failing or
peeling, use a paint stripper such as BEHR PREMIUM No. 992 Concrete & Masonry
Paint Stripper to remove old coating or scrape/sand down to a sound concrete
surface. Scuff sand glossy surfaces. Clean and spot etch any exposed concrete using
a product such as a BEHR PREMIUM No. 991 Concrete & Masonry Cleaner & Etcher.
Remove all dust with a damp cloth, allow to dry.
PRIME
Interior Wood: Use a product such as BEHR PREMIUM PLUS
®
No. 75 All-In-One
Primer & Sealer. Exterior Wood: Use a product such as BEHR PREMIUM PLUS
No. 436 Multi-Surface Primer & Sealer. Interior/Exterior Concrete or Masonry:
Over uncoated surfaces, use a product such as BEHR PREMIUM No. 880
Concrete & Masonry Bonding Primer.
APPLICATION
Use product when the surface and air temperatures are between 50 - 90° F
(10 - 32° C). Stir paint occasionally. When working with more than one can of the
same product, intermix to ensure colour uniformity. Use a high quality 10-13 mm
nap roller cover, nylon/polyester brush or an airless sprayer (.015 - .021" spray tip,
60 mesh filter). Spread rate varies, depending on the surface texture, porosity and
application method. Additional coats may be required for optimal hide and durability.
Do not thin if using a roller or brush; however, if using a sprayer and thinning is
required, thin with water at a rate of no more than 250 mL per 3.79 L.
DRY TIME
Longer dry time required in cooler temperatures and in higher humidity.
Allow 72 hours before subjecting to normal use. After 30 days, cured paint
film may be cleaned with a mild, non-abrasive liquid detergent. Dry paint film
is mildew resistant.
DISPOSAL
Properly dispose of all soiled rags. For disposal of empty containers and unused
product, contact your household refuse collection service.
†
WARNING! If you scrape, sand or remove old paint, you may release lead dust.
LEAD IS TOXIC. Contact the National Lead Information Center at 1-800-424-LEAD
or log on to www.epa.gov/lead
LIMITED WARRANTY If this product is found to be defective upon inspection by
an expert, Behr Process Corporation will, at its option, and upon presentation of
proof-of-purchase (the original receipt), either furnish an equivalent amount
of new product or refund the original purchase price of this product to you.
This warranty is not transferable. If you believe this product is defective, contact
Behr Process Corporation at 2750 Centre Avenue N.E., Calgary, AB T2A2L3.
The cost of transportation or shipping, if any, are to be assumed by the consumer.
The clause of limitation of liability which follows is inapplicable in Quebec:
This warranty excludes (1) labour and costs of labour for the application or
removal of any product, and (2) any incidental or consequential damages,
whether based on breach of express or implied warranty, negligence,
strict liability or any other legal theory. The above provisions are not intended to
operate where prohibited by law. This limited warranty is the only warranty provided
by Behr Process Corporation unless extended by a provincial consumer statute.
To consult with a Behr Certified Coatings Professional, call 1-800-661-1591.