Use and Care Manual

©2021 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. (C.O.V.) <50 g/L • REV. 06/21
No. 6050 Ultra Pure White
No. 6300 Deep Base
No. 6695 Slate Gray
BEHR PREMIUM
®
Low-Lustre Enamel
Porch & Patio Floor Paint
• Interior/Exterior Mildew Resistant Finish
• 100% Acrylic Latex
• Available in Custom Colors
• Resists Cracking & Peeling
• Withstands Scuffing & Fading
Spread Rate:
Rough 200-300 Sq. Ft.
Smooth 300-400 Sq. Ft.
Protect
from Freezing
Dry Time:
1 Hr. Dry to Touch.
4-6 Hr. Recoat
Clean-Up:
Soap & Water
CAUTION: Painted surfaces may become slippery when wet. Adding a non-skid floor
additive may help prevent slipping.
WHERE TO USE
On properly prepared or previously painted Interior/Exterior surfaces.
Ideal for Porches, Floors, Decks, Basement Floors, Patios, Siding, Trim, Furniture and
Trellises. Do not use on areas subject to automotive tires.
PREPARATION
†
(Proper Surface Preparation is Required.)
• All surfaces must be clean, sound, dry and free of any dirt, oil and grease.
• Remove mildew stains with a mildew stain removing product.
• New or Weathered Wood: Use a product such as BEHR PREMIUM® No. 63 All-In-One
Wood Cleaner. Lightly sand to remove remaining wood fibers/fuzz.
• Painted Surfaces-Wood: For a painted surface in sound condition, use a product to
clean and prepare the surface. If the coating is failing or peeling, use a paint stripper
to remove old coating. Scuff sand glossy surfaces. Use stainless steel or galvanized
nails to prevent nail staining. Countersink nail heads, repair imperfections and sand
smooth. Remove all dust with a damp cloth, allow to dry.
• Uncoated Concrete or Masonry Surfaces: Allow new surfaces to cure 30 days.
Clean and etch surface using a product such as a muriatic acid etcher (read and
follow all manufacturer’s label directions) to achieve a textured profile similar to
150 grit sandpaper. Wipe your fingers over the clean, dry floor to check for dust or
powder. Ensure there is no residue on your fingers that may have been left from the
etcher. If residue is found, rinse the surface to remove residue. Allow the surface to
dry completely. Sprinkle a few drops of water onto the surface. If water is quickly
absorbed and the surface feels like 150 grit sandpaper, the surface is ready. If not,
re-etch.
• Painted Surfaces-Concrete: For a painted surface in sound condition, use a product to
clean and prepare the surface. If the coating is failing or peeling, use a paint stripper
to remove old coating or scrape/sand down to a sound concrete surface. Scuff sand
glossy surfaces. Clean and spot etch any exposed concrete. Remove all dust with a
damp cloth, allow to dry.
PRIME
• Interior Wood: Use a product such as BEHR PREMIUM PLUS® No. 75 All-In-One
Primer & Sealer.
• Exterior Wood: Use a product such as BEHR PREMIUM PLUS No. 436 Multi-Surface
Primer & Sealer.
• Interior/Exterior Concrete or Masonry: Over uncoated surfaces, use a product such
as BEHR PREMIUM No. 880 Concrete & Masonry Bonding Primer.
APPLICATION
• Use product when the surface and air temperatures are between 50-90° F (10-32° C).
• Stir paint occasionally.
• When working with more than one can of the same product, intermix to ensure
color uniformity.
• Use a high quality 3/8 - 1/2” nap roller cover, nylon/polyester brush or an airless sprayer
(.015 - .021” spray tip, 60 mesh filter).
• Spread rate varies, depending on the surface texture, porosity and application method.
• Additional coats may be required to ensure proper coverage, optimal hide and durability.
• Do not thin if using a roller or brush; however, if using a sprayer and thinning is required,
thin with water at a rate of no more than 1/2 pint per gallon.
DRY TIME
• Longer dry time required in cooler temperatures and in higher humidity. Allow 72 hours
before subjecting to normal use. After 30 days, cured paint film may be cleaned with
a mild, non-abrasive liquid detergent. Dry paint film is mildew resistant.
DISPOSAL
• Properly dispose of all soiled rags. For disposal of empty containers and unused
product, contact your household refuse collection service.
LIMITED WARRANTY
Visit behr.com/warranty or call 1-800-854-0133 Ext. 2 for more information.
†
WARNING! If you scrape, sand or remove old paint, you may release lead
dust. LEAD IS TOXIC. Contact the National Lead Information Center at
1-800-424-LEAD or log on to www.epa.gov/lead
WARNING Cancer and Reproductive Harm www.P65Warnings.ca.gov
WARNING! CAUSES EYE AND SKIN IRRITATION. MAY CAUSE RESPIRATORY TRACT IRRITATION.
CONTAINS: DIURON, ETHYLHEXYL BENZOATE, CARBON BLACK, CRYSTALLINE SILICA AND
TITANIUM DIOXIDE. Avoid contact with skin and eyes and avoid breathing vapors, spray mist and
sanding dust. Sanding, grinding or abrading may release sanding dust, which may be harmful if
inhaled and has been shown to cause lung damage or cancer with long term exposure. Do not
breathe dusts, vapor, or spray mist. To avoid breathing in dust, vapors, and spray mist, open windows
and doors or use other means to ensure fresh air entry during application, drying, sanding, and/
or abrading. If properly used, a respirator (NIOSH approved with particulate pre-filter) may offer
additional protection and should be used if adequate ventilation cannot be provided; obtain
professional advice before using. If you experience eye watering, headaches, or dizziness during
application or drying, increase fresh air or leave the area. Avoid contact with eyes and skin. Wash
thoroughly after handling. Close container after each use. FIRST AID: If you experience difficulty
in breathing, leave the area to obtain fresh air. If continued difficulty is experience, get medical
assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 20
minutes and get medical attention; for skin, wash thoroughly with soap and water. If swallowed, get
medical attention immediately. KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.