Use and Care Manual
BEHR PREMIUM
®
Cabinet, Door & Trim Enamel
Interior/Exterior Semi-Gloss
• Door Won’t Stick After 2 Hours of Dry Time*
• Excellent Flow & Leveling
• Dries to a Hard, Durable Finish
• Easy Clean Surface
• Resists Dirt, Grime & Household Chemicals
• All-Weather Protection
• Sandable
• Soap & Water Clean-Up
• Mildew-Resistant Paint Finish
No. 7120 White
No. 7123 Deep Base
2 Coats Required
for Optimal Durability
Spread Rate:
Up to 400 sq ft
Coverage
Dry Time:
1 Hr. Dry to Touch
2 Hr. Recoat
Clean-Up:
Soap & Water
WHITE: READY TO USE OR ADD TINTING COLORANTS.
DEEP BASE: DO NOT USE WITHOUT THE ADDITION OF TINTING COLORANTS.
PROTECT FROM FREEZING.
WHERE TO USE
Interior or exterior wood, drywall, masonry, vinyl, aluminum, and other
properly prepared and primed surfaces. Ideal for cabinets, doors, trim,
molding, windows & shutters.
SURFACE PREPARATION
†
(Proper Surface Preparation Is Required.)
• All surfaces must be clean, sound, dry and free of any dirt, oil and
grease stains.
• Remove mildew stains with a mildew stain removing product.
• Interior Wood Trim, Door & Cabinets: Remove all loose and peeling
paint; scuff sand glossy surfaces; caulk and repair imperfections. Sand
all wood surfaces in the direction of the wood grain to the desired
smoothness. Remove all dust from sanded surfaces with a damp,
lint-free cloth.
• Exterior Wood: Use a product such as BEHR PREMIUM
®
No. 63
All-In-One Wood Cleaner. Thoroughly rinse the treated surfaces with
clean water and allow to dry before any paint application.
• Interior/Exterior Concrete & Masonry: Allow new stucco, plaster and
masonry to cure for 30 days. Use a concrete & masonry degreaser &
cleaner to clean and prepare the surface. Powerwash to remove chalk on
exterior surfaces.
• Interior/Exterior Metal: Etch galvanized metal.
• For primed surfaces, sand primer coat prior to topcoating for best results.
PRIME
• Priming is recommended over all properly prepared coated or
uncoated surfaces.
• For all interior surfaces, use a product such as BEHR
®
Kitchen, Bath &
Trim Interior Stain-Blocking Primer & Sealer No. 75.
• For all exterior surfaces, use a product such as BEHR Acrylic-Alkyd
Enamel Undercoater No. 437 or BEHR Multi-Surface Interior/Exterior
Stain-Blocking Primer & Sealer No. 436.
• Follow all label instructions.
APPLICATION
• DO NOT THIN.
• Stir before and during application.
• When working with more than one can of the same product, intermix to
ensure color uniformity.
• Certain colors may require 2 or more coats to achieve complete hide.
• Apply when air temperature is between 50–90° F.
• Brush: Apply a thin coat using a high quality synthetic brush. For best
results, apply paint with a high quality 100% Nylon brush.
• Roller: Use a high quality 1/4" nap roller cover.
• Airless Sprayer: .013"–.015" spray tip, 60 mesh filter.
• OPTIONAL: In between coats, sand lightly with 320-400 grit
sand paper.
• NOTE: If touch-up is necessary, same application method is
recommended.
DRY TIME
• *Darker colors may require additional dry time. Longer dry time
required in cooler temperatures and higher humidity.
• Cabinets, doors and windows can be closed as early as 2 hours
after final topcoat.
• After 2 weeks, cured paint film may be cleaned with a mild,
non-abrasive liquid detergent. Dry paint film is mildew resistant.
• Do not use on floors.
DISPOSAL
• Properly dispose of all soiled rags.
• For disposal of empty containers and unused product, contact your
household refuse collection service.
• To reduce waste, consult with your retailer or an online paint
calculator to determine the correct amount of paint to purchase.
LIMITED WARRANTY
• Visit www.behr.com/warranty or call 1-800-854-0133 Ext. 2 for more
information.
†
WARNING If you scrape, sand or remove old paint, you may release lead
dust. LEAD IS TOXIC. Contact the National Lead Information Center at
1-800-424-LEAD or log on to www.epa.gov/lead.
WARNING
Cancer and Reproductive Harm – www.P65Warnings.ca.gov.
WARNING! CAUSES EYE AND SKIN IRRITATION. MAY CAUSE RESPIRATORY TRACT
IRRITATION. MAY CONTAIN: CRYSTALLINE SILICA AND TITANIUM DIOXIDE. AVOID CONTACT
WITH SKIN AND EYES AND AVOID BREATHING VAPORS, SPRAY MIST AND SANDING DUST.
Sanding, grinding or abrading may release sanding dust, which may be harmful if inhaled and
has been shown to cause lung damage or cancer with long term exposure. Do not breathe
dusts, vapor, or spray mist. To avoid breathing in dust, vapors, and spray mist, open windows
and doors or use other means to ensure fresh air entry during application, drying, sanding,
and/or abrading. If properly used, a respirator (NIOSH approved with particulate pre-lter) may
offer additional protection and should be used if adequate ventilation cannot be provided;
obtain professional advice before using. If you experience eye watering, headaches, or
dizziness during application or drying, increase fresh air or leave the area. Avoid contact with
eyes and skin. Wash thoroughly after handling. Close container after each use. FIRST AID: If
you experience difculty in breathing, leave the area to obtain fresh air. If continued difculty is
experience, get medical assistance immediately. In case of eye contact, ush immediately with
plenty of water for at least 20 minutes and get medical attention; for skin, wash thoroughly
with soap and water. If swallowed, get medical attention immediately.
KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY.
©2022 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. < 50 g/L • REV. 3/22