Use and Care Manual

©2021Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. <50 g/L • REV. 6/21
WHITE: READY TO USE OR ADD TINTING COLORANTS.
DEEP BASE: DO NOT USE WITHOUT THE ADDITION OF TINTING COLORANTS.
PROTECT FROM FREEZING.
No. 7120 White
No. 7123 Deep Base
Cabinet & Trim Enamel Interior Semi-Gloss
• Resists Dirt, Grime &
Household Chemicals
• Sandable
• Soap & Water Clean-Up
• Mildew-Resistant Paint Finish
• Door Won’t Stick After 2 Hours
of Dry Time*
• Excellent Flow & Leveling
• Dries to a Hard, Durable Finish
• Easy Clean Surface
2 Coats Required
for Optimal Durability
Clean-Up:
Soap & Water
Dry Time:
1 Hr. Dry to Touch
2 Hr. Recoat
Spread Rate:
Up to 400 sq ft Coverage
WHERE TO USE
Recommended for interior wood, drywall, masonry, vinyl and other
properly prepared and primed surfaces. Ideal for kitchen and bathroom
cabinets and doors, windows, trim & molding.
SURFACE PREPARATION
†
(Proper Surface Preparation is Required.)
• All surfaces must be clean, sound, dry and free of any dirt, oil and
grease stains.
• Remove mildew stains with a mildew stain removing product.
• Remove all loose and peeling paint; scuff sand glossy surfaces; caulk
and repair imperfections.
†
Sand all wood surfaces in the direction
of the wood grain to the desired smoothness. Remove all dust from
sanded surfaces with a damp, lint free cloth and allow to dry.
PRIME
• Priming is recommended on all surfaces. On previously painted
surfaces and on new wood, masonry and vinyl surfaces, or on
surfaces with heavy stains, prime with a product such as
BEHR
®
Kitchen, Bath & Trim Primer & Sealer No. 75 prior to
topcoating with this product. Follow all label instructions.
For best results, sand primer coat prior to topcoating.
APPLICATION
• Apply when air temperature is between 50-90° F (10-32° C).
• Stir before and during application.
• When working with more than one can of the same product, intermix
to ensure color uniformity.
• Do not thin.
• Brush: Apply a thin coat using a high quality synthetic brush. For best
results, apply paint with a high quality 100% Nylon brush.
• Roller: Use a high quality 1/4” nap roller cover.
• Airless Sprayer: .013” - .015” spray tip, 60 mesh filter.
• OPTIONAL: In between coats, sand lightly with 320-400 grit sand paper.
• Certain colors may require 2 or more coats to achieve complete hide.
• NOTE: If touch-up is necessary, same application method is
recommended.
DRY TIME
• * Darker colors may require additional dry time. Longer dry time
required in cooler temperatures and higher humidity.
• Cabinets, doors and windows can be closed as early as 2 hours
after final topcoat.
• After 2 weeks, cured paint film may be cleaned with a mild,
non-abrasive liquid detergent. Dry paint film is mildew resistant.
• Do not use on floors.
DISPOSAL
• Properly dispose of all soiled rags.
• For disposal of empty containers and unused product, contact your
household refuse collection service.
• To reduce waste, consult with your retailer or an online paint
calculator to determine the correct amount of paint to purchase.
LIMITED WARRANTY
• Visit www.behr.com/warranty or call 1-800-854-0133 Ext. 2 for more
information.
†
WARNING If you scrape, sand or remove old paint, you may release lead
dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS,
SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved respirator to control
lead exposure. Clean up carefully with a HEPA vacuum and a wet mob. Before
you start, find out how to protect yourself and your family by contacting the
National Lead Information Center at 1-800-424-LEAD or log on to www.epa.
gov/lead
WARNING! CAUSES EYE AND SKIN IRRITATION. MAY CAUSE
RESPIRATORY TRACT IRRITATION. CONTAINS: CRYSTALLINE SILICA
TITANIUM DIOXIDE. AVOID CONTACT WITH SKIN AND EYES AND AVOID
BREATHING VAPORS, SPRAY MIST AND SANDING DUST. Sanding, grinding or
abrading may release sanding dust, which may be harmful if inhaled and has been show to
cause lung damage or cancer with long term exposure. Do not breathe dust, vapors, or spray
mist. To avoid breathing in dust, papers, and spray mist, open windows and doors or use
other means to ensure fresh air entry during application, drying, Sanding, and/or abrading.
Improperly used, a respirator (NIOSH approved with particulate pre-filter) may offer additional
protection and should be used if adequate ventilation Cannot be provided; Team professional
advice before using. Experience I watering, headaches, or dizziness during application or
drawing, increased fresh air or leave the area. Boy contact with eyes and skin. Wash it. Close
container after each use. FIRST AID: if you experience difficulty in breathing, leave the area
to obtain fresh air. If continued difficulty is experience, get medical assistance in mediately.
In case of iContact, immediately was plenty of water for at least 20 minutes can get medical
attention; foreskin, wash soap and water. If swallowed, get medical attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY.
WARNING Cancer and Reproductive Harm – www.P65Warnings.ca.gov.