TDS
TECHNICAL DATA SHEETTECHNICAL DATA SHEET
CABINET & TRIM INTERIOR SEMIGLOSS ENAMEL
NO. 7120 WHITE
PRODUCT INFORMATION
BEHR PREMIUM® Cabinet & Trim Interior Semi-Gloss Enamel oers excellent ow & leveling and dries to a hard, durable nish.
Its outstanding block resistance allows for quick return to service, making it ideal for use on cabinets, trim, doors, windows,
shutters and woodwork. This product can also be used on other properly prepared and primed substrates, such as drywall,
masonry and metal.
RECOMMENDED USES:
Ideal for properly prepared and primed new and previously painted interior substrates such as:
• Wood • Engineered Wood • Architectural Plastics • Drywall/Gypsum Board • Plaster
• Concrete • Masonry • Brick • Concrete Masonry Units • Steel
• Galvanized Steel • Aluminum • Other Ferrous Metals • Other Non-Ferrous Metals
COMPLIES WITH THE BELOW AS OF 6/1/2020
SCAQMD YES LADCO YES
CARB SCM 2007 YES AIM YES
OTC PHASE II YES GREENGUARD®
#
YES
OTC YES LEED® v.4
†
YES
#
GREENGUARD is a registered trademark of UL Company.
†
Please visit www.usgbc.org/LEED for additional details.
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 7120 White Base 124 oz / 6 oz
No. 7123 Deep Base 116 oz / 10 oz
Gloss: 40 – 50 @ 60°
Resin Type: Acrylic
Weight per Gallon: 10.9 lb
% Solids by Volume: 36% ± 2%
% Solids by Weight: 51% ± 2%
VOC: < 50 g/L
Flash Point: N/A
Viscosity: 85 – 95 KU
Recommended Film Thickness:
1st Coat Wet: 4.6 mils / Dry: 1.6 mils @ 350 sq ft/gal
2nd Coat Wet: 4.0 mils / Dry: 1.4 mils @ 400 sq ft/gal
Two (2) coats are required for optimum protection.
Coverage: 350 – 400 sq ft/gal depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon brush for best results
Roller: 1/4" nap roller cover
Airless Spray:
Tip: .013" – .015"
Filter: 60 mesh
Fluid Pressure: 1,400 – 2,400 psi
Thinning: DO NOT THIN. Product is formulated for use at
package consistency.
Dry Time: @ 77°F & 50% RH
To Touch: 1 hour
To Recoat: 2 hours
Full Cure: 7 days
Dry times are temperature, humidity, and lm thickness
dependent.
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling
paint, rust and all other foreign substances.
Wood: Remove mill glaze with sandpaper to open the pores
of the wood and follow all label instructions. For severe
stains caused by mold, mildew, algae and fungus, apply
a mildew stain removing product. Set nails and ll holes,
scratches, and gouges with the appropriate wood ller and
let dry completely. Remove all dust with a wiping cloth. Fill
all gaps with a 100% acrylic, siliconized, paintable caulking
and allow to dry completely. Patched and lled surfaces
should be sanded smooth and dusted clean prior to coating.
Prime with a suitable primer.
Drywall: All drywall surfaces should be suciently sanded
smooth. Remove any remaining drywall dust prior to
priming. Allow all drywall compounds to be completely dry
prior to coating. Prime with a suitable primer.
Masonry: The pH must be 10 or lower prior to coating.
Smooth masonry may require an adequate prole for
adhesion. For all other smooth trowel concrete, create
an adequate prole for adhesion using a product such as
muriatic acid etcher or with mechanical means. Remove all
loose aggregate and debris. Prime the area with an
alkali-resistant primer.
Plaster: New plaster should be thoroughly dried out and
cured for a minimum of 30 days before painting. When
cured, clean using a mixed solution of one part vinegar
and one part water to remove eorescence and neutralize.
Prime the area with an alkali-resistant primer.
Steel: Minimum surface preparation is Hand Tool Cleaning
in accordance with SSPC-SP2. Remove all oil and grease
from the surface with a solvent in accordance with SSPC-SP1.
For optimal performance, use Commercial Blast Cleaning in
accordance with SSPC-SP6. Prime the area with a
rust-inhibitive primer the same day as cleaned.
Galvanized Steel: Solvent clean new galvanized metal in
accordance with SSPC-SP1 to remove oil and grease from
the surface. Pre-treat with a phosphoric acid solution or
a commercially-available etching solution. Galvanized
metal that has been passivated with chromates or silicates
may require brush blasting in accordance with SSPC-SP16
to remove these treatments. Rusty galvanizing requires
a minimum of Hand Tool Cleaning in accordance with
SSPCSP2. Prime the area the same day as cleaned.
Aluminum: Remove all oil and grease from the surface with
a solvent in accordance with SSPC-SP1. Prime the area the
same day as cleaned.
Stain-Blocking: After priming, test for stain bleed-through
by applying the topcoat to a small section. If the stain bleeds
through the topcoat, apply a second coat of primer and
test again before topcoating the entire area. If bleeding
continues, primer may need a longer dry time before
applying topcoat.
Previously Painted Surfaces: Remove all loose and
peeling paint and all other foreign substances. Clean any
dirt and grease by scrubbing the surface with a detergent
and water solution, followed by a thorough rinsing with
clean water. Set nails and ll holes, scratches, and gouges
with the appropriate wood ller and let dry completely.
Remove all dust with a tack or wiping cloth. Fill all gaps with
a 100% acrylic, siliconized, paintable caulking, and allow to
completely dry prior to coating.
Glossy Surfaces: For maximum adhesion, sand the surface
thoroughly to provide a rough surface before coating.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other nature
are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 6/2020
1 of 2