Specification
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2014 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 11/2015
1 of 2
INTERIOR/EXTERIOR DIRECTTOMETAL GLOSS PAINT
NO. 8200 WHITE
PRODUCT INFORMATION
BEHR PREMIUM® Interior/Exterior Direct-To-Metal Gloss paint is 100% styrene acrylic and provides excellent corrosion and ash
rust resistance. Engineered for excellent adhesion to a variety of properly prepared or primed residential and light commercial
metal surfaces. Intended for use in conditions of repeated heavy abrasion, including mechanical wear and repeated scrubbing with
industrial solvents, cleaners and scouring agents. Provides a durable gloss nish that withstands tough elements on both interior
and exterior surfaces. Suitable for use in USDA inspected facilities
RECOMMENDED USES:
Ideal for properly prepared coated and uncoated interior and exterior:
• Ferrous Metal • Non-Ferrous Metal • Gypsum Board • Plaster
• Concrete • CMU • Masonry • Wood
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 8200 124 oz./6 oz.
No. 8230 116 oz./10 oz.
Pre-Mixed colors:
No. 8210 Red
No. 8214 Yellow
No. 8220 Black
Gloss: >70 @ 60°
Resin Type: Styrene Acrylic
Weight per Gallon: 10.0 lbs.
% Solids by Volume: 34.62%
% Solids by Weight: 46%
VOC: <100 g/L
Flash Point: N/A
Viscosity: 95-105 KU
Recommended Film Thickness:
1st Coat Wet: 5.0 Dry: 1.75 mils @ 350-400 Sq. Ft./Gal.
2nd Coat Wet: 3.0 Dry: 1.1 mils @ 350-400 Sq. Ft./Gal.
Coverage: 350-400 Sq. Ft./Gal. depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: High Quality Synthetic
Roller: 1/4"- 3/8" mohair, foam, ocked or nap woven cover
Airless Spray: At packaged consistency
Tip: .009"- .017"
Filter: 60 mesh
Thinning: Not recommended. Product is formulated for use
at package consistency only.
Dry Time: @ 77° & 50% RH
To Touch: 1 hour
To Recoat: 3 hours
Full Cure: 4 weeks
SURFACE PREPARATION:
All surfaces must be clean, dry, free of rust, dust, dirt, chalk,
oil, grease, wax, polish, mold and mildew stains, loose and
peeling paint and all other foreign substances.
UNPAINTED METAL SURFACES: Ferrous Metals: Use
SSPC-SP2. Remove all rust and mill scale using sandpaper,
ferrous metal, abrasive blasting, or other abrading methods
to create a prole on the metal’s surface. Remove any
residue, and clean the metal by scrubbing the surface with a
solvent such as mineral spirits or acetone. Bare metal must
be coated the same day it is cleaned.
Ferrous and Non Ferrous Metals: Use SSPC-SP1. All oil
lm on new metal must be removed before it is painted.
Remove oil lm with a solvent such as mineral spirits or
acetone and remove any residue. Sand the surface with
sandpaper, ferrous metal, or by using a chemical etcher.
Clean by scrubbing the surface with a solvent such as
mineral spirits or acetone and remove any residue.
Previously Painted Metal Surfaces: Remove all
loose and peeling paint and all other foreign substances.
Clean any dirt and grease by scrubbing the surface with a
solvent such as mineral spirits or acetone and remove any
residue. Suciently sand and dull all smooth, hard, dense or
glossy surfaces before coating for maximum performance.
It is recommended to test a small inconspicuous area for
adhesion one week prior to application. If test area shows
insucient adhesion, additional abrasion or complete
removal of the previous coating may be required. All exterior
alkyd surfaces should be primed prior to painting.
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC. Contact the
National Lead Information Center at 1-800-424-LEAD or
visit www.epa.gov/lead.
RECOMMENDED PRIMER/SYSTEMS:
UNPAINTED METAL SURFACES:
Ferrous Metals: Self priming on properly prepared
substrates. For best results, use a MPI #107 certied
rust-inhibitive, water-based primer, such as
BEHR PREMIUM PLUS® Exterior Multi-Surface Primer &
Sealer No. 436. To properly prepare the uncoated surface,
please refer to the surface preparation instructions.
Ferrous and Non-Ferrous Metals: Use a MPI #134
certied water-based primer for non-ferrous surfaces, such
as BEHR PREMIUM PLUS Exterior Multi-Surface Primer &
Sealer No. 436. To properly prepare the uncoated surface,
please refer to the surface preparation instructions.
PREVIOUSLY PAINTED METAL & GLOSSY SURFACES:
Self priming on properly prepared substrates. Use a MPI
#134 certied water-based primer for galvanized surfaces,
such as BEHR PREMIUM PLUS Exterior Multi-Surface Primer
& Sealer NO. 436. To properly prepare the uncoated surface,
please refer to the surface preparation instructions.
TEST SPECIFICATIONS:
Abrasion Resistance:
Test Method: ASTM D4060, CS17
wheel, 1000 cycles, 1 kg load
Result: <50 mg loss
Accelerated Weathering:
Test Method: ASTM D4587, QUV-A, 1,000 hours
Results: Pass
Direct Impact Resistance:
Test Method: ASTM D2794 (>160 in. lbs)
Result: Pass
Adhesion:
Test Method: ASTM D4541, CRS
Result: >300 psi
Test Method: ASTM D3359, aluminum
Result: 5B
COMPLIES WITH THE BELOW AS OF 9/1/2014
SCAQMD YES LADCO YES
CARB YES AIM YES
OTC YES LEED v.3 (2009)
†
YES
MPI# 154