TDS

TECHNICAL DATA SHEETTECHNICAL DATA SHEET
INTERIOR/EXTERIOR
CONCRETE & GARAGE 1PART EPOXY COATING
NO. 900 WHITE BASE
PRODUCT INFORMATION
A high-performance, ready-to-use water-based coating that is designed to resist hot tire pickup and marring. This self-priming satin
nish is resistant to household-type chemicals, oil and gasoline, which reduces the need for maintenance of hard-to-clean interior or
exterior oors. This durable coating also resists scung, fading, cracking, peeling and blistering.
COMPLIES WITH THE BELOW AS OF 3/1/2020
SCAQMD YES OTC YES
CARB SCM 2007 YES LADCO YES
OTC Phase II YES AIM YES
RECOMMENDED USES:
Use on properly prepared interior or exterior horizontal concrete surfaces such as: Garage Floors, Driveways, Basement Floors,
Porches and Pool Decks. NOT for industrial applications, such as areas subject to fork lifts.
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 900 White Base 122  oz / 8  oz
No. 930 Deep Base 116  oz / 14  oz
Pre-mixed Colors:
No. 901 Silver Gray
No. 902 Slate Gray
Gloss: 10-20 @ 60°
Resin Type: Acrylic/Epoxy
Weight per Gallon: 10.2 lb
% Solids by Volume: 32% ± 2%
% Solids by Weight: 44% ± 2%
VOC: < 50 g/L
Flash Point: N/A
Viscosity: 75-85 KU (after tinting)
Recommended Film Thickness:
Wet: 5.3 mils / Dry: 1.6 mils @ 300 sq ft/gal
Wet: 3.2 mils / Dry: 1.0 mils @ 500 sq ft/gal
Coverage: 300-500 sq ft/gal depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8” – 1/2” nap roller cover, depending on surface
texture
Airless Spray:
Tip: .015”- .021”
Filter: 60 mesh
Fluid Pressure: 1,400 - 2,400 psi
Thinning: Do Not Thin.
Dry Time: @ 77°F & 50% RH
To Touch: 1 hour
Recoat: 4 to 6 hours
Dry times are temperature, humidity, and lm thickness
dependent. The oor may be subjected to light foot
trac after 24 hours. Allow surface to dry 72 hours
before subjecting to heavy foot trac or repositioning
furniture. Allow 7 days before subjecting painted surface
to automobile tires. Apply an additional coat for optimal
hide and durability.
SURFACE PREPARATION:
New and Uncoated Concrete or Masonry Surfaces:
New concrete must cure for a minimum of 30 days.
For proper penetration and adhesion of topcoat, use a
product such as a muriatic acid to clean and etch the surface.
Follow all label instructions. Apply a Primer Coat: Apply 1
coat of BEHR PREMIUM® Concrete & Garage 1-Part Epoxy
Coating or a product such as BEHR PREMIUM Concrete &
Masonry Bonding Primer No. 880 to increase adhesion of
topcoat to the surface.
Painted, Stained or Sealed Concrete: For a painted
surface in sound condition, use a product to clean and
prepare the surface. If the coating is failing or peeling,
use a paint stripper to remove old coating or scrape/sand
down to a sound concrete surface. Scusand glossy surfaces.
Clean and spot-etch any exposed concrete. Remove all dust
with a damp cloth, allow to dry. Spot-prime all bare concrete
areas with BEHR PREMIUM Concrete & Garage 1-Part Epoxy
Coating or with a product such as BEHR PREMIUM No. 880
Concrete & Masonry Bonding Primer to increase adhesion of
topcoat to the surface.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEANUP/DISPOSAL:
Clean all tools and equipment with warm, soapy water.
Do not dispose of this product down a drain. If spilled,
contain material and remove with an inert absorbent.
Dispose of contaminated absorbent, container and unused
product in accordance with all current federal, state
and local regulations. For recycling or disposal of empty
containers, unused product and soiled rags, contact your
household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
•
For best results, apply when air, material and surface
temperatures are between 50°F and 90°F. Do not apply in
direct sunlight. Temperatures above 90°F can cause the
paint to dry too fast, whereas temperatures below 50°F
can inhibit proper lm formation. Do not apply if rain
or heavy dew is expected within 24 hours. NOTE: If the
surface is hot to the touch it should be considered too hot
to apply this coating.
•
DO NOT use on above-grade vertical surfaces or areas
subject to hydrostatic pressure.
•
Allow 30 days before washing or cleaning for full cure.
•
An annual touch-up may be required in areas subject to
tire trac.
•
Shelf life under normal conditions is 2 years unopened.
GENERAL INFORMATION:
WARNING! CAUSES EYE AND SKIN IRRITATION.
MAY CAUSE RESPIRATORY TRACT IRRITATION. CONTAINS:
CRYSTALLINE SILICA AND TITANIUM DIOXIDE. Avoid contact
with skin and eyes and avoid breathing vapors, spray mist
and sanding dust. Sanding, grinding or abrading may
release sanding dust, which may be harmful if inhaled and
has been shown to cause lung damage or cancer with long
term exposure. Do not breathe dusts, vapor, or spray mist.
To avoid breathing in dust, vapors, and spray mist, open
windows and doors or use other means to ensure fresh air
entry during application, drying, sanding, and/or abrading.
If properly used, a respirator (NIOSH approved with
This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other nature
are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 5/2020
1 of 2