TDS
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2014 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 11/2015
1 of 1
CONCRETE & MASONRY PROTECTOR & WATERPROOFER
NO. 980
PRODUCT INFORMATION
BEHR PREMIUM® Concrete & Masonry Protector & Waterproofer is a premium, interior/exterior, waterproong formula that
uses the latest water-based, silicone technology designed to penetrate surfaces up to 1/2". This waterproofer creates a barrier
inside the surface that keeps water out, but lets trapped water vapors escape; reducing corrosion, spalling, eorescence
and freeze-thaw damage. It reduces staining due to mold and mildew, and ensures greater durability of the surface.
The protection is not worn away with normal use. It protects long after the water beading is gone.
RECOMMENDED USES:
Properly prepared interior or exterior, vertical or horizontal unnished concrete, stone and tile surfaces, such as:
• Concrete • Concrete Aggregate • Unglazed Tile
• Brick • Natural & Articial Stone • Stucco
Not recommended for use on areas subject to hydrostatic pressure such as basement walls or oors.
PRODUCT SPECIFICATIONS:
Fill Level:
No. 980 128 oz. / Gal.
Active Type: Silane/Siloxane
Weight per Gallon: 8.3 lbs.
% Solids by Volume: 6.2%
% Solids by Weight: 6.0%
VOC: <120 g/L
Flash Point: N/A
Viscosity: 25-35 sec (#1 Zahn cup)
Coverage: 250 Sq. Ft./Gal., depending on application
method and substrate porosity. Does not include the loss
of material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller:
Smooth Surface: 3/8"-1/2" nap
Rough Surface: 1/2"-3/4" nap
Airless Spray: At packaged consistency
Tip: .015"- .019"
Filter: 60 mesh
Pump Sprayer: At packaged consistency.
Thinning: Not recommended. Product is formulated for use
at package consistency.
Dry Time: 75°F & 50% RH
Longer dry time may be required in cooler temperatures
and higher humidity.
To Recoat: 2-4 hours
Full Cure: 24-48 days
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling
paint, rust, and all other foreign substances.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Center at 1-800-424-LEAD or log on
to www.epa.gov/lead.
CLEAN UP:
Clean all tools and equipment with clean water.
For proper disposal of empty containers and unused
product, contact your household refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Do not use on coated or previously sealed oors.
• For best results, apply at temperatures between
50°F - 90°F. Temperatures above 90°F may aect the
application such as drying to fast. Avoid applying in
direct sun. NOTE: If the surface is hot to the touch it
should be considered too hot to apply this coating.
• Allow two weeks before washing or cleaning for full cure.
• Shelf life under normal conditions is two years unopened.
• Masonry with pH Levels up to 13.0.
GENERAL INFORMATION:
Warning! Causes eye and skin irritation. Wear protective
clothing, gloves, eye, and face protection. Do not eat, drink,
or smoke when using this product. Take o contaminated
clothing and wash it before reuse. Wash hands thoroughly
after handling. Dispose of unused, contents, container and
other contaminated wastes in accordance with local, state,
federal and provincial regulations.
First aid: If in eyes: Rinse cautiously with water for
several minutes and remove contacts if present and easy to
do. Continue rinsing and get medical attention if eye irritation
persists. If on skin: Wash with plenty of soap and water.
If swallowed: Rinse mouth and get medical attention
if you feel unwell.
COMPLIES WITH THE BELOW AS OF 9/1/2014
SCAQMD YES AIM YES
CARB YES LEED v.3 (2009)
†
YES
OTC YES MPI# 117
LADCO YES
†
Please visit www.usgbc.org/LEED for additional details.