Use and Care Manual

LIMITED WARRANTY For three years from the date of purchase, Behr Process
Corporation warrants to the original consumer purchaser, (1) that the product meets
Behr Process Corporation’s manufacturing specications, and (2) the performance of
this product when applied according to the label instructions and specications. If this
product is found not to perform as specied on the label within three years from the
date of purchase, Behr Process Corporation will, at its option and upon presentation
of proof-of-purchase (the original receipt), either furnish an equivalent amount
of new product or refund the original purchase price of this product to you. This
warranty excludes (1) labor and costs of labor for the application or removal of
any product, and (2) any incidental or consequential damages, whether based
on breach of express or implied warranty, negligence, strict liability or any
other legal theory. Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion may not apply to
you. To the extent permitted by applicable law, any implied warranties including
the implied warranties of merchantability and of tness for a particular purpose,
are limited to the duration of this express warranty. To obtain warranty service, call
1-800-854-0133. Behr Process Corporation reserves the right to inspect any and all
application of the product prior to processing your claim made under this warranty.
To consult with a Behr Certied Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).
WARNING! IRRITANT. CAUSES EYE AND SKIN IRRITATION. MAY CAUSE RESPIRATORY TRACT
IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING VAPORS,
SPRAY MIST AND SANDING DUST. SANDING, GRINDING OR ABRADING MAY RELEASE
SANDING DUST, WHICH MAY BE HARMFUL IF INHALED AND HAS BEEN SHOWN TO CAUSE
LUNG DAMAGE OR CANCER WITH LONG TERM EXPOSURE.To avoid breathing in dust, vapors,
and spray mist, open windows and doors or use other means to ensure fresh air entry during
application, drying, sanding, and/or abrading. If properly used, a respirator (NIOSH approved
with particulate pre-lter) may offer additional protection and should be used if adequate
ventilation cannot be provided; obtain professional advice before using. If you experience eye
watering, headaches, or dizziness during application or drying, increase fresh air or leave the
area. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after
each use. FIRST AID: If you experience difculty in breathing, leave the area to obtain fresh air. If
continued difculty is experienced, get medical assistance immediately. In case of eye contact,
ush immediately with plenty of water for at least 20 minutes and get medical attention; for
skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately.
KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY
WARNING: This product can expose you to chemicals including ethylene glycol, which is
known to the State of California to cause birth defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov.
©2022 Behr Process Corp.
Santa Ana, CA 92705 U.S.A.
behr.com
V.O.C. <120 g/L (Low Solids)
REV 7/22
CAUTION: Surfaces may become slippery when wet. Use caution
when walking on surface when moisture is present.
WHERE TO USE:
Horizontal and vertical uncoated porous natural stones and masonry surfaces such
as: concrete pavers, agstone, slate, limestone, sandstone, brick, cobblestone,
stacked stone, and more. Do not use on smooth, glazed, or polished surfaces. Not
recommended for use on areas subject to hydrostatic pressure such as basement
walls or oors. NOTE: SURFACE MAY APPEAR SLIGHTLY DARKER. IT IS ADVISABLE
TO TEST THE PRODUCT ON AN INCONSPICUOUS AREA BEFORE GENERAL
APPLICATION TO ENSURE THE DESIRED APPEARANCE IS ACHIEVED.
PREPARATION (Proper surface preparation is required)
• All surfaces must be clean, sound, dry, and free of any dirt, oil, and grease.
• Remove all dirt, oil, or grease using a cleaner/degreasing product or detergent.
Follow all manufacturer’s label instructions.
• Use a paint stripper to remove any previous coatings or sealers. Follow all
manufacturer’s label instructions.
• Test: Sprinkle a few drops of water onto the surface.
• If water is quickly absorbed and the surface feels like 150 grit sandpaper, the
surface is ready.
• If water beads or rolls off the surface, additional cleaning may be necessary.
APPLICATION
• DO NOT THIN.
• Stir or mix product thoroughly before and occasionally during application.
BEHR PREMIUM
®
Color Enhancing Sealer
• Deepens & Enriches Colors Found in Porous Substrates
• Water Resistant
• Penetrating Formula
• Interior/Exterior & Horizontal/Vertical Surfaces
• Ideal for Porous Natural Stones, Bricks, and Pavers
No. 982 Natural
Coverage:
175-400 Sq. Ft.
Depending On Porosity
Protect
From Freezing
Dry Time:
24-72 Hrs. To Cure
Apply
Until Saturated
• Use product when air and surface temperature is between 50–90° F (10-32° C).
• Apply using a high quality pump sprayer, 1/4” – 3/8” nap roller, synthetic brush,
or a sponge pad applicator until saturated. Multiple coats may be necessary on
very porous surfaces. Apply within 24 hours of initial application.
• DO NOT ALLOW PRODUCT TO POOL. Remove any puddles by back rolling using a
nap roller or by wiping up excess with a clean cloth before it cures.
• On vertical surfaces, apply from the bottom up and saturate well. Avoid dripping
and clean up any excess with a clean cloth before it cures.
DRY TIME
• Longer dry time required in cooler temperatures and in higher humidity.
• Water and stain repellency starts to develop within 24 hours.
• Allow 24-72 hours before subjecting surface to automotive tires, heavy foot
trafc, or repositioning furniture.
• Wait at least 30 days before rinsing or cleaning.
DISPOSAL
• Properly dispose of all soiled applicators and rags after use and protect unused
product from freezing.
• For disposal of empty containers and unused product, contact your household
refuse collection service.
† WARNING! If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. Contact the National Lead Information Center
at 1-800-424-LEAD or log on to www.epa.gov/lead.