Use and Care Manual

BEHR PRO
®
i100 Interior Dead Flat
• High Hide
• Good Touch-Up
WHERE TO USE
Ideal for walls and ceilings in high turnover properties.
PREPARATION
All surfaces should be properly prepared and cleaned.
Remove loose paint, wash off dirt and grease with detergent,
rinse and allow to dry. Remove mildew stains with a mildew
stain removing product. Scuff sand glossy surfaces and
repair imperfections. Remove all dust with a damp cloth,
allow to dry. Allow new concrete, plaster and masonry to
cure for 30 days before painting.
PRIME
Prime new drywall with a product such as KILZ
®
PVA Drywall
Primer or BEHR PREMIUM PLUS
®
No. 73 Drywall Primer &
Sealer. For stain-blocking, or over oil-based or glossy surfaces,
use a product such as BEHR PREMIUM PLUS Interior/Exterior
Multi-Surface Primer & Sealer No. 436. For disaster restoration
use a product such as water-base KILZ MAX
®
Primer or oil-base
KILZ Original Primer to permanently block severe stains and
odors. After priming, test for stain bleed-through by applying
the topcoat to a small section. If the stain bleeds through the
topcoat, apply a second coat of primer and test again before
top-coating the entire area. If bleeding continues, allow primer to
dry a full 24 hours before top-coating. Prime all metal surfaces
before painting.
APPLICATION
Apply when air and surface temperatures are between 35-90 °F
(2-32 °C). Stir paint occasionally. Intermix containers of same
product to ensure color and sheen uniformity. Use a high quality
3/8”-3/4” nap roller cover, nylon/polyester brush or airless
sprayer (.017 - .021" spray tip, 60 mesh filter). Product is
formulated for use at package consistency only. DO NOT THIN.
Cooler temperatures or higher humidity may prolong drying time.
After 2 weeks, cured paint film may be cleaned with a mild, non-
abrasive liquid detergent.
DISPOSAL
For disposal of empty containers, unused paint and soiled rags,
contact your household refuse collection service.
Visit behr.com for painting tips, project advice and color coordination
with the ColorSmart by BEHR
®
Tool, or download the ColorSmart by
BEHR App on your mobile device.
©2018 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. (C.O.V.) < 50 g/L • REV. 08/18
No. PR110 White Base
1 Hr Dry Time
2 Hr Recoat Time
300-400 sq ft
Coverage per Gallon
Protect
from Freezing
Soap & Water
Clean-Up
*LIMITED WARRANTY For one year from the date of purchase, Behr Process Corporation warrants
to the original consumer purchaser, (1) that the product meets Behr Process Corporation’s
manufacturing specifications, and (2) the performance of this product when applied according to
the label instructions and specifications. In the event this product proves to be defective within one
year from the date of purchase, Behr Process Corporation will, at its option and upon presentation
of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product
or refund the original purchase price of this product to you. This warranty excludes (1) labor
and costs of labor for the application or removal of any product, and (2) any incidental
or consequential damages, whether based on breach of express or implied warranty,
negligence, strict liability or any other legal theory. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you. To the extent permitted by applicable law, any implied warranties including
the implied warranties of merchantability and of fitness for a particular purpose, are
limited to the duration of this express warranty. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives
you specific legal rights and you may also have other rights, which vary from state to state. Note
to residents of the State of New Jersey: The provisions of this warranty, including its limitations,
are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To
obtain warranty service, call 1-800-854-0133 ext.2. Behr Process Corporation reserves the right
to inspect any and all applications of the product prior to processing your claim made under this
warranty.
To consult with a Behr Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).
CAUTION IRRITANT MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID
CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS AND SPRAY
MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH
ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows
and doors or use other means to ensure fresh air entry during application and drying.
If you experience eye watering, headaches or dizziness, increase fresh air. If properly used, a respirator
(NIOSH approved for organic vapor with P series particulate pre-filter) may offer additional protection;
obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid
contact with eyes and skin. Wash thoroughly after handling. Close container after each use. FIRST
AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is
experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty
of water for at least 20 minutes and get medical attention; for skin, wash thoroughly with soap and
water. If swallowed, get medical attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY.
WARNING Cancer and Reproductive Harm – www.P65Warnings.ca.gov
WARNING! If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. Contact the National Lead Information Center
at 1-800-424-LEAD or log on to www.epa.gov/lead.