TDS
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2015 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
*This product does not protect users against food-borne (or disease-causing) bacteria.
Revised 11/2015
PRODUCT INFORMATION
BEHR PRO™ Interior Dead Flat Paint is a ZERO VOC* professional quality, non-reective latex paint with superior hide and
coverage, excellent sprayability, spray back-roll and superior touch-up. This product contains an antimicrobial agent to
protect the surface of the paint lm from mold and mildew.*
RECOMMENDED USES:
Use on properly prepared primer or previously painted surfaces. Ideal for family rooms, living rooms, dining rooms,
bedrooms and ceilings.
• Concrete • Concrete Block/CMU • Brick • Plaster
• Drywall/Gypsum Board • Wood • Plywood • Ferrous Metals
• Non-Ferrous Metals • Architectural Plastics
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 310 124 oz. /6 oz.
No. 314 117 oz. /13 oz.
No. 313 116 oz. /14 oz.
Gloss: 0-3 @ 60°
Sheen: 0-3 @ 85°
Resin Type: 100% VAE
Weight per Gallon: 11.7 lbs.
% Solids by Volume: 42%
% Solids by Weight: 57%
*VOC: < 5 g/L
Flash Point: N/A
Viscosity: 95-105 KU
Recommended Film Thickness:
Wet: 5.3 mils; Dry: 2.15 mils @ 300 Sq. Ft./Gal.
Wet: 4.0 mils; Dry: 1.65 mils @ 400 Sq. Ft./Gal.
Coverage: 300 – 400 Sq. Ft./Gal. depending on the surface
texture, porosity and application method. Does not include
the loss of material from spraying. Film thickness depends
on porosity and various substrate irregularities.
APPLICATION:
Brush: Nylon / Polyester Blend
Roller:
Smooth Surfaces: 3/8" - 1/2" nap
Rough Surfaces: 1/2" - 3/4" nap
Airless Spray: Fluid pressure of 2,000 - 3,200 psi
Tip: .015" - .021"
Filter: 60 mesh
Thinning: Not recommended. Product is formulated for
use at package consistency only.
Dry Time: 77°F (25°C), 50% RH:
Longer dry time required in cooler temperatures and
in higher humidity.
To Touch: 1 hours
To Recoat: 2 hours
Full Cure: 2 weeks
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling
paint, rust and all other foreign substances.
New Drywall: All drywall surfaces should be suciently
sanded smooth. Remove any remaining drywall dust prior
to priming. Allow all drywall compounds to be completely
dry prior to coating. Previously Painted Drywall: Remove
all loose and peeling paint and all other foreign substances.
Clean any dirt and grease by scrubbing the surface with
a detergent and water solution, followed by a thorough
rinsing with clean water. Set nails and ll holes, scratches,
and gouges with the appropriate spackling material. Let dry
completely and sand smooth. Remove all dust with a wiping
cloth. Fill all gaps with a 100% acrylic, siliconized, paintable
caulking, and allow to completely dry prior to coating.
Glossy Surfaces: For maximum adhesion, sand the surface
thoroughly before coating.
New Wood: Remove mill glaze with sandpaper. Set nails and
ll holes, scratches, and gouges with the appropriate wood
ller and let dry completely. Remove all dust with a wiping
cloth. Fill all gaps with a 100% acrylic, siliconized, paintable
caulking, and allow to completely dry prior to coating.
Previously Painted Wood: Remove all loose and peeling
paint and all other foreign substances. Clean any dirt and
grease by scrubbing the surface with a detergent and
water solution, followed by a thorough rinsing with clean
water. Set nails and ll holes, scratches, and gouges with
the appropriate wood ller and let dry completely.
Remove all dust with a tack or wiping cloth. Fill all gaps with
a 100% acrylic, siliconized, paintable caulking, and allow to
completely dry prior to coating. Glossy Surfaces:
For maximum adhesion, sand the surface thoroughly
before coating.
Wood: WARNING! Sanding or scraping pressure treated
lumber may be hazardous; wear appropriate protection.
New Plaster: New plaster should be thoroughly dried
out and cured for a minimum of 30 days before painting.
When cured, clean using a mixed solution of one part
vinegar and one part water to remove eorescence and
neutralize.Previously Painted Plaster: Remove all
loose and peeling paint and all other foreign substances.
Clean any dirt and grease by scrubbing the surface with
a detergent and water solution, followed by a thorough
rinsing with clean water. Set nails and ll holes, scratches,
and gouges with the appropriate spackling material. Let dry
completely and sand smooth. Remove all dust with a tack
or wiping cloth. Fill all gaps with a 100% acrylic, siliconized,
paintable caulking, and allow to completely dry prior to
coating.Glossy Surfaces: For maximum adhesion, sand the
surface thoroughly before coating.
Stainblocking: After priming, test for stain bleed-through
by applying the topcoat to a small section. If the stain bleeds
through the topcoat, apply a second coat of primer and
test again before top-coating the entire area. If bleeding
continues, a longer dry time of the primer may be needed
before top-coating.
Masonry: All masonry surfaces must be cured at least
30 days before painting. The pH must be 10.0 or lower prior
to coating. Smooth masonry may require an adequate
prole for adhesion. For all other smooth trowel concrete,
create a prole using a product such as a muriatic acid etcher
or with mechanical means..
Metals: Ferrous and Non-Ferrous Metals: All metals
should be clean and free of any oils, rust, mill scale or other
contaminants. All metals require sucient “tooth” or prole
for optimum adhesion and therefore require some type of
sanding, abrasion, or chemical etching.
1 of 2
i300
INTERIOR DEAD FLAT PAINT
NO. 310
COMPLIES WITH THE BELOW AS OF 2/1/2015
SCAQMD YES MPI# 53, 143
CARB YES MPI X-GREEN 53, 143
OTC YES GREENGUARD® YES
LADCO YES CHPS YES
AIM YES NAHB/ICC NGBS YES
LEED v.3 (2009)
†
YES
LEED v.4
†
YES
†
Please visit www.usgbc.org/LEED for additional details.
GREENGUARD is a registered trademark of UL Company.