Use and Care Manual

BEHR PRO
®
e600 Exterior Satin
• 100% Acrylic
• High Hide & Good Adhesion
• Mildew Resistant Coating
• Low Temperature Application
WHERE TO USE
Ideal for both commercial and residential properties over
properly prepared and primed exterior surfaces of wood,
hardboard, aluminum siding, vinyl siding, fiber cement siding,
stucco, concrete, masonry, brick and metal.
PREPARATION & PRIME
Countersink nailheads, fill and sand smooth. Remove rust, loose
or peeling paint. Repair imperfections and sand smooth. Wash
off dirt, grease and chalk with detergent and/or powerwash.
Remove mildew stains with a mildew stain removing product.
Clean and sand new or weathered wood. Scuff sand or degloss
smooth or glossy surfaces. Scuff sand or etch metals. Rinse and
allow to dry. Caulk windows, doors and other openings. Allow
new stucco, plaster and masonry to cure for 30 days before
painting. For stain-blocking, painting over woods with tannins,
or over oil-based or glossy surfaces, prime with a product such
as BEHR PREMIUM PLUS Interior/Exterior Multi-Surface Primer
& Sealer No. 436. For drastic color changes or when applying
deep colors denoted with a dagger (†) on the color chip, apply a
custom tinted primer if needed. Prime all metal surfaces before
painting.
APPLICATION
Apply product on dry substrates when air and surface
temperatures are between 35°-90°F (2°-32°C) and will remain
between 35°-90°F (2°-32°C) for at least 4 hours after applying.
Do not paint when rain or heavy condensation is expected. Stir
paint occasionally. Intermix containers of same product to ensure
color and sheen uniformity. On semi-smooth surfaces, use a high
quality 3/8-1/2” nap roller cover, nylon/polyester brush or an
airless sprayer (.015 -.021” spray tip, 60 mesh filter). On rough
surfaces, use a high quality 3/4-1” nap roller cover. Certain
colors may require additional coats for complete hide. On heavy
stains and woods that contain tannins, allow 12-16 hours of dry
time between coats.Cooler temperatures or higher humidity may
prolong drying time. Dry paint film is mildew resistant. When
applying to vinyl, color choice must be the same color or lighter
than the existing color. Do not use on floors.
DISPOSAL
For disposal of empty containers, unused paint and soiled rags,
contact your household refuse collection service.
Visit behr.com for painting tips, project advice and color coordination
with the ColorSmart by BEHR
®
Tool, or download the ColorSmart by
BEHR App on your mobile device.
©2018 Behr Process Corporation
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. (C.O.V.) < 50 g/L • REV. 08/18
FOR MEDIUM AND DEEP BASES – DO NOT USE WITHOUT THE ADDITION OF TINTING COLORANTS
No. PR640 White Base
No. PR643 Deep Base
No. PR644 Medium Base
2 Hr Dry Time
4 Hr Recoat Time
250-400 sq ft
Coverage per Gallon
Protect
from Freezing
Soap & Water
Clean-Up
*LIMITED WARRANTY For one year from the date of purchase, Behr Process Corporation warrants
to the original consumer purchaser, (1) that the product meets Behr Process Corporation’s
manufacturing specifications, and (2) the performance of this product when applied according to
the label instructions and specifications. In the event this product proves to be defective within one
year from the date of purchase, Behr Process Corporation will, at its option and upon presentation
of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product
or refund the original purchase price of this product to you. This warranty excludes (1) labor
and costs of labor for the application or removal of any product, and (2) any incidental
or consequential damages, whether based on breach of express or implied warranty,
negligence, strict liability or any other legal theory. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you. To the extent permitted by applicable law, any implied warranties including
the implied warranties of merchantability and of fitness for a particular purpose, are
limited to the duration of this express warranty. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives
you specific legal rights and you may also have other rights, which vary from state to state. Note
to residents of the State of New Jersey: The provisions of this warranty, including its limitations,
are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To
obtain warranty service, call 1-800-854-0133 ext.2. Behr Process Corporation reserves the right
to inspect any and all applications of the product prior to processing your claim made under this
warranty..
To consult with a Behr Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).
CAUTION IRRITANT MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID
CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS AND SPRAY
MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH
ADEQUATE VENTILATION.
To avoid breathing vapors and spray mist, open windows
and doors or use other means to ensure fresh air entry during application and drying.
If you experience eye watering, headaches or dizziness, increase fresh air. If properly used, a respirator
(NIOSH approved for organic vapor with P series particulate pre-filter) may offer additional protection;
obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid
contact with eyes and skin. Wash thoroughly after handling. Close container after each use. FIRST
AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is
experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty
of water for at least 20 minutes and get medical attention; for skin, wash thoroughly with soap and
water. If swallowed, get medical attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN – DO NOT TAKE INTERNALLY.
WARNING Cancer and Reproductive Harm – www.P65Warnings.ca.gov
WARNING! If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. Contact the National Lead Information Center
at 1-800-424-LEAD or log on to www.epa.gov/lead.