TDS
TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2019 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 8/2019
2 of 2
Previously Painted Surfaces: Remove all loose and
peeling paint and all other foreign substances. Clean any
dirt and grease by scrubbing the surface with a detergent
and water solution, followed by a thorough rinsing with
clean water. Set nails and ll holes, scratches, and gouges
with the appropriate wood ller and let dry completely.
Remove all dust with a tack or wiping cloth. Fill all gaps with
a 100% acrylic, siliconized, paintable caulking, and allow to
completely dry prior to coating.
Glossy Surfaces: For maximum adhesion, sand the surface
thoroughly to provide a rough surface before coating.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, nd out how to
protect yourself and your family by contacting the National
Lead Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
SYSTEM RECOMMENDATIONS:
Although BEHR ULTRA™ is a paint & primer in one (self-
priming - rst coat is the primer and the second coat is
the nish) over most properly prepared surfaces, it is
recommended for optimum performance to follow the
primer recommendations provided below:
Drywall/Gypsum Wallboard:
• Self-prime using 2 coats of BEHR ULTRA Interior Paint
or
• 1 coat BEHR® Drywall Plus Interior Primer & Sealer No. 73
2 coats BEHR ULTRA Interior Paint
Masonry:
• Self-prime using 2 coats of BEHR ULTRA Interior Paint
or
• 1 coat BEHR Drywall Plus Interior Primer & Sealer No. 73
2 coats BEHR ULTRA Interior Paint
Plaster:
• Self-prime using 2 coats of BEHR ULTRA Interior Paint
or
• 1 coat BEHR Drywall Plus Interior Primer & Sealer No. 73
2 coats BEHR ULTRA Interior Paint
Wood:
• Self-prime using 2 coats of BEHR ULTRA Interior Paint
or
• 1 coat BEHR Drywall Plus Interior Primer & Sealer No. 73
2 coats BEHR ULTRA Interior Paint
Stain-Blocking:
• Self-prime using 2 coats of BEHR ULTRA Interior Paint
or
• 1 coat BEHR Kitchen, Bath & Trim Interior Stain-Blocking
Primer & Sealer No. 75 or BEHR Multi-Surface Interior/
Exterior Stain-Blocking Primer & Sealer No. 436
2 coats BEHR ULTRA Interior Paint
Ferrous and Non-Ferrous Metals:
• 1 coat BEHR Interior/Exterior Metal Primer No. 435
(recommended for optimal corrosion resistance
or when priming over sound rusty metal surfaces)
or BEHR Multi-Surface Interior/Exterior Stain-Blocking
Primer & Sealer No. 436
2 coats BEHR ULTRA Interior Paint
PERFORMANCE DATA:
Flexibility
ASTM D522, method B - Pass
Scrubbability
ASTM D2486, > 3000 (no shim)
Sealing Properties
ASTM E97, < 7% Change in Reectance
Burnish
ASTM D6736, < 15% Sheen Change
Washability
ASTM D4828 - Pass
CLEANUP/DISPOSAL:
Clean all tools and equipment with warm, soapy water. Do
not dispose of this product down a drain. If spilled, contain
material and remove with an inert absorbent. Dispose of
contaminated absorbent, container and unused product
in accordance with all current federal, state and local
regulations. For recycling or disposal of empty containers,
unused product and soiled rags, contact your household
refuse collection service.
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Do not use on oors.
• For best results, apply when air, material and surface
temperatures are between 50°F and 90°F. Temperatures
above 90°F can cause the paint to dry too fast, whereas
temperatures below 50°F can inhibit proper lm
formation.
• Allow 4 weeks before washing or cleaning for full cure.
• Shelf life under normal conditions is 2 years unopened.
GENERAL INFORMATION:
CAUTION IRRITANT MAY CAUSE EYE, NOSE AND THROAT
IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND
AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE
PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH
ADEQUATE VENTILATION. To avoid breathing vapors and
spray mist, open windows an doors or use other means to
ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase
fresh air. If properly used, a respirator (NIOSH approved for
organic vapor with P series particulate pre-lter) may oer
additional protection; obtain professional advice before
using. A dust mask does not provide protection against
vapors. Avoid contact with eyes and skin. Wash thoroughly
after handling. Close container after each use.
FIRST AID: If you experience diculty in breathing,
leave the area to obtain fresh air. If continued diculty is
experienced, get medical assistance immediately. In case of
eye contact, ush immediately with plenty of water for at
least 20 minutes and get medical attention; for skin, wash
thoroughly with soap and water. If swallowed, get medical
attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN – DO NOT
TAKE INTERNALLY.
INTERIOR MATTE PAINT
NO. 1750 ULTRA PURE WHITE®