No. 1750 Ultra Pure White
No. 1753 Deep Base**
No. 1754 Medium Base
• Stain-Blocking Paint & Primer In One
• Excellent Durability &
Hide in Fewer Coats
• Extra-Durable Paint Film
• Stain & Scuff Resistant
• Washable, Easy-Clean Finish
• Lifetime Warranty*
• Low VOC, 100% Acrylic
The extra protective shell, featuring NANOGUARD
Technology, offers a
STAYS LOOKING NEW LONGER
Finish for excellent durability.
WHERE TO USE
Properly prepared coated and uncoated Interior surfaces. Ideal for
Family Rooms, Living Rooms, Dining Rooms, Bedrooms, Hallways
PREPARATION & PRIME
All surfaces should be properly prepared and cleaned. Remove loose
paint, wash off dirt and grease with detergent, rinse and allow to dry.
Remove mildew stains with a mildew stain remover. Scuff sand glossy
surfaces and repair imperfections. Remove all dust with a damp cloth,
allow to dry. Allow new stucco, plaster and masonry to cure for 30
days before painting. Use BEHR ULTRA
Paint as a primer for properly
prepared uncoated or painted interior surfaces, including woods that
contain tannins (two primer coats required for redwood and cedar) and
heavily stained areas. Lock in stains with BEHR ULTRA Paint as a spot
primer. For heavy stains, test for stain bleed-through by applying BEHR
ULTRA Paint to a small section. If the stain bleeds through, spot prime
another coat to the stained area and test again before topcoating. If
bleeding continues, a longer dry time is needed before topcoating. For
drastic color changes or when applying deep colors denoted with a
dagger (†) on the color chip, apply a tinted primer coat of BEHR ULTRA
Paint if needed.
Apply when air and surface temperatures are between 50-90°F
(10-32°C). Stir paint occasionally. Intermix containers of same
product to ensure color and sheen uniformity. Use a high quality
3/8-1/2" nap roller cover, nylon/polyester brush or an airless sprayer
(.015 - .019" spray tip, 60 mesh filter). Do not thin if using a roller or
brush; however, if using a sprayer and thinning is required, thin with
water at a rate of no more than 1/2 pint per gallon. Certain colors may
require additional coats for complete hide. Darker colors may require
additional dry time between coats. Cooler temperatures or higher
humidity may prolong drying time. After 4 weeks, cured paint film may
be cleaned with a mild, non-abrasive liquid detergent. Dry paint film is
mildew resistant. Do not use on floors.
For disposal of empty containers, unused paint and soiled rags, contact
your household refuse collection service.
Visit Behr.com for painting tips, expert project advice and the perfect
color coordination with the ColorSmart by BEHR
WARNING! If you scrape, sand or remove old paint, you may release
lead dust. LEAD IS TOXIC. Contact the National Lead Information Center
at 1-800-424-LEAD or log on to www.epa.gov/lead.
*LIFETIME LIMITED WARRANTY Behr Process Corporation warrants to the original residential
consumer purchaser the performance of this product as described on this label for so long
as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT
PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE
WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not
to perform as specified upon inspection by our representative during the warranty period,
Behr Process Corporation will, at its option and upon presentation of proof-of-purchase
(the original receipt), either furnish an equivalent amount of new product or refund the original
purchase price of this product to you. This warranty excludes (1) labor and costs of labor
for the application or removal of any product, and (2) any incidental or consequential
damages, whether based on breach of express or implied warranty, negligence, strict
liability or any other legal theory. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to
you. This warranty gives you specific legal rights and you may also have other rights, which
vary from state to state.
To consult with a Behr Certified Coatings Professional, call 1-800-854-0133 Ext. 2 (U.S.A. only).
©2019 BEHR PROCESS CORPORATION
Santa Ana, CA 92705 U.S.A. • behr.com
V.O.C. (C.O.V.) <50 g/L • REV: 06/19
FOR TINT BASES – DO NOT USE WITHOUT THE ADDITION OF TINTING COLORANTS
1 Hr Dry Time
2 Hr Recoat Time
250-400 Sq. Ft.
Coverage per Gallon
Soap & Water
CAUTION! IRRITANT! HARMFUL IF SWALLOWED. MAY CAUSE EYE, NOSE AND THROAT
IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS
AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH
ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and
doors or use other means to ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase fresh air. If properly used, a
respirator (NIOSH approved for organic vapor with P series particulate pre-filter) may offer
additional protection; obtain professional advice before using. A dust mask does not provide
protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling.
Close container after each use. FIRST AID: If you experience difficulty in breathing, leave
the area to obtain fresh air. If continued difficulty is experienced, get medical assistance
immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes
and get medical attention; for skin, wash thoroughly with soap and water. If swallowed,
get medical attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.
WARNING! This product contains chemicals known to the state of California to cause cancer
and birth defects or other reproductive harm.
** Contains Ethylene Glycol