TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either expressed or implied, of merchantability, tness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a Behr Certied Coatings Professional,
call 1-800-854-0133 Ext. 2 (U.S.A. only). ©2017 Behr Process Corporation Santa Ana, CA 92704 U.S.A.
Revised 1/2017
1 of 2
INTERIOR SEMIGLOSS ENAMEL PAINT
NO. 3750 ULTRA PURE WHITE®
PRODUCT INFORMATION
BEHR PREMIUM PLUS ULTRA® Interior Semi-Gloss Enamel Paint is a 100% acrylic paint and primer in one with advanced stain-blocking
formula that will change the way you paint. This product, featuring NANOGUARD® Technology, forms an extra-protective shell that
oers outstanding stain, scu, mar and antimicrobial-mildew resistance and an easy-to-clean, STAYS LOOKING NEW LONGER®
Finish with superior stain removal. This sophisticated color palette delivers exceptional hide and maximum moisture resistance.
RECOMMENDED USES:
Use on properly prepared, coated and uncoated, interior surfaces such as:
• Concrete • Concrete Block/CMU • Brick • Plaster
• Drywall/Gypsum Board • Wood • Ferrous Metals • Galvanized Steel
• Aluminum • Other Non-Ferrous Metal • Architectural Plastics
PRODUCT SPECIFICATIONS:
Tint Bases/Max Tint Load:
No. 3750 128 oz. / 2 oz.
No. 3754 120 oz. / 10 oz.
No. 3753 116 oz. / 14 oz.
Gloss: 45-55 @ 60°
Resin Type: 100% Acrylic
Weight per Gallon: 10.43 lbs.
% Solids by Volume: 37.45%
% Solids by Weight: 49.77%
VOC: <50 g/L
Flash Point: N/A
Viscosity: 95-105 KU
Recommended Film Thickness:
Wet: 6.4 mils / Dry: 2.4 mils @ 250 Sq. Ft./Gal.
Wet: 4.0 mils / Dry: 1.5 mils @ 400 Sq. Ft./Gal.
Coverage: 250-400 Sq. Ft./Gal. depending on application
method and substrate porosity. Does not include the loss of
material from spraying.
APPLICATION:
Brush: Nylon/polyester
Roller: 3/8" - 1/2" nap
Airless Spray: At packaged consistency
Tip: .015"- .019"
Filter: 60 mesh
Thinning: (If required) No more than 1/2 pint
of water per gallon.
Dry Time: @ 77° & 50% RH
Longer dry time may be required in cooler temperatures
and higher humidity.
To Touch: 1 hour
To Recoat: 2 hours
Full Cure: 4 weeks
SURFACE PREPARATION:
All surfaces must be clean, free of dust, chalk, oil, grease,
wax, polish, mold and mildew stains, loose and peeling
paint, rust, and all other foreign substances.
New Drywall: All drywall surfaces should be suciently
sanded smooth. Remove any remaining drywall dust prior
to priming. Allow all drywall compounds to be completely
dry prior to coating. Previously Painted Drywall: Remove
all loose and peeling paint and all other foreign substances.
Clean any dirt and grease by scrubbing the surface with
a detergent and water solution, followed by a thorough
rinsing with clean water. Set nails and ll holes, scratches,
and gouges with the appropriate spackling material.
Let dry completely and sand smooth. Remove all dust with
a wiping cloth. Fill all gaps with a 100% acrylic, siliconized,
paintable caulking, and allow to completely dry prior to
coating. Glossy Surfaces: For maximum adhesion,
sand the surface thoroughly before coating.
New Wood: Remove mill glaze with sandpaper.
Set nails and ll holes, scratches, and gouges with the
appropriate wood ller and let dry completely.
Remove all dust with a wiping cloth. Fill all gaps
with a 100% acrylic, siliconized, paintable caulking,
and allow to completely dry prior to coating.
Previously Painted Wood: Remove all loose and peeling
paint and all other foreign substances. Clean any dirt and
grease by scrubbing the surface with a detergent and water
solution, followed by a thorough rinsing with clean water.
Set nails and ll holes, scratches, and gouges with the
appropriate wood ller and let dry completely.
Remove all dust with a tack or wiping cloth.
Fill all gaps with a 100% acrylic, siliconized, paintable
caulking, and allow to completely dry prior to coating.
Glossy Surfaces: For maximum adhesion, sand the
surface thoroughly before coating.
Wood: WARNING! Sanding or scraping pressure treated
lumber may be hazardous; wear appropriate protection.
New Plaster: New plaster should be thoroughly dried
out and cured for a minimum of 30 days before painting.
When cured, clean using a mixed solution of one part
vinegar and one part water to remove eorescence and
neutralize. Previously Painted Plaster: Remove all
loose and peeling paint and all other foreign substances.
Clean any dirt and grease by scrubbing the surface with
a detergent and water solution, followed by a thorough
rinsing with clean water. Set nails and ll holes, scratches,
and gouges with the appropriate spackling material. Let dry
completely and sand smooth. Remove all dust with a tack
or wiping cloth. Fill all gaps with a 100% acrylic, siliconized,
paintable caulking, and allow to completely dry prior to
coating. Glossy Surfaces: For maximum adhesion,
sand the surface thoroughly before coating.
Stain-blocking: After priming, test for stain bleed-through
by applying the topcoat to a small section. If the stain bleeds
through the topcoat, apply a second coat of primer and
test again before top-coating the entire area. If bleeding
continues, a longer dry time of the primer may be needed
before top-coating.
Masonry: All masonry surfaces must be cured at least
30 days before painting. The pH must be 10.0 or lower prior
to coating. Smooth masonry may require an adequate
prole for adhesion. For all other smooth concrete, create a
prole using a product such as a muriatic acid etcher or with
mechanical means. Remove loose aggregate and debris.
Ferrous and Non-Ferrous Metal: The oil lm on new
COMPLIES WITH THE BELOW AS OF 1/1/2017
SCAQMD YES LEED v.4
YES
CARB YES MPI# 54
OTC YES MPI X-GREEN 54
LADCO YES GREENGUARD® YES
AIM YES CHPS YES
LEED v.3 (2009)
YES NAHB/ICC NGBS YES
This coating conforms to USDA regulatory requirements
for incidental food-contact materials intended for use on
surfaces not in direct contact with food, such as walls, oors
and ceilings.
Please visit www.usgbc.org/LEED for additional details.
GREENGUARD is a registered trademark of UL Company.

Summary of content (2 pages)